cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
945
Views
0
Helpful
6
Replies
Highlighted
Beginner

Not Display Caller name from Siemen IP Phone to Cisco IP Phone

Dear all,

I have a problem when siemen ip phone call to cisco ip phone, it not display caller name.

But cisco ip phone call to siemen ip phone is show caller name.

It can display caller name when I use CUCM version 6.1 but now I upgrade to CUCM 8.5 already.

My diagram

cisco ip phone (4605) <--> router (MGCP) <--> PBX (Siemen) <--> siemen ip phone

(5959)

I debug isdn q931 and show this result

Jul 29 12:34:09.825 TH: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8  callref = 0x098F

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech 

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA98381

                Exclusive, Channel 1

        Facility i = 0x9FAA06800100820100A1180201000201008010507261736F6E672E4C75202D20494354

        Calling Party Number i = 0x0081, '4605'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0x80, '5959'

                Plan:Unknown, Type:Unknown

Jul 29 12:34:09.885 TH: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8  callref = 0x898F

        Channel ID i = 0xA98381

                Exclusive, Channel 1

Jul 29 12:34:09.925 TH: ISDN Se0/0/0:15 Q931: RX <- ALERTING pd = 8  callref = 0x898F

        Facility i = 0x9FAA068001008201008B0100A1150202DCA506082B0C02885302010603050011000000

        Facility i = 0x9FAA068001008201008B0100A10F0202DCB402015530068204061C0840

        Facility i = 0x9FAA068001008201008B0100A1170202DCC3020101A10E040949342D4F4E53495445020101

        Facility i = 0x9FAA068001008201018B0100A14A0202DCD206082B0C028853020100303A810C0C06008035393539740200C0822A031902000410000000600000040400C00E38008F048005000088836301C37C0A8349342D4F4E53495445

        Progress Ind i = 0x8088 - In-band info or appropriate now available

Jul 29 12:34:11.233 TH: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8  callref = 0x098F

        Cause i = 0x8090 - Normal call clearing

Jul 29 12:34:11.341 TH: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8  callref = 0x898F

        Cause i = 0x8090 - Normal call clearing

Jul 29 12:34:11.349 TH: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x098F

How I configure any command at voice gateway or change at CUCM.

Please help.

Thank you

6 REPLIES 6
Highlighted
Beginner

Not Display Caller name from Siemen IP Phone to Cisco IP Phone

Hi

are these checked under the port which is connect to the siemen PBX ?

Highlighted
Beginner

Not Display Caller name from Siemen IP Phone to Cisco IP Phone

Hi Linuxchild,

I try already but still not display.

Please help

Thank you

Highlighted
Beginner

Not Display Caller name from Siemen IP Phone to Cisco IP Phone

Hello

I don't know if this has relation to your installation

but I have found this

Calling Line (Number) Identification Restriction (CLIR) is not supported by the Siemens PBX for outgoing calls. The PBX does honor CLIR on incoming calls, however.

http://www.ciscopaw.net/en/US/docs/voice_ip_comm/cucme/pbx/interop/notes/571119nt.pdf

Beginner

Re: Not Display Caller name from Siemen IP Phone to Cisco IP Pho

Hi,

I have worked with CUCM <>H323 GW <> E1 ISDN <> Siemens PBX and CLID works fine in both direction. Could you post your debug output in the other way direction (Siemens calls Cisco).

Thanks!

Highlighted

Re: Not Display Caller name from Siemen IP Phone to Cisco IP Pho

Hi

Have you checked 'Send Calling Name in Facility IE' on the E1 config page?

Try that and reset.

Aaron

Aaron Please remember to rate helpful posts to identify useful responses, and mark 'Answered' if appropriate!
Highlighted
Beginner

Re: Not Display Caller name from Siemen IP Phone to Cisco IP Pho

Hi

I configure MGCP this below

Then I cannot configure anything.

Thank you.

CreatePlease to create content