10-06-2013 05:31 AM - edited 03-16-2019 07:43 PM
Dear All
i have 2901 router , i configured on ntp , after two days the time changed , how to solve this ?
VG-KC(config)#do sh ntp sta
Clock is synchronized, stratum 5, reference is 127.127.7.1
nominal freq is 250.0000 Hz, actual freq is 250.0275 Hz, precision is 2**18
reference time is D5FBD6EF.E19F58F3 (15:32:47.881 kuwaitz Sun Oct 6 2013)
clock offset is 0.0000 msec, root delay is 0.00 msec
root dispersion is 375.02 msec, peer dispersion is 375.02 msec
VG-KC#sh ntp associations
address ref clock st when poll reach delay offset disp
*~127.127.7.1 127.127.7.1 4 36 64 377 0.0 0.00 0.0
~212.26.18.43 0.0.0.0 16 - 64 0 0.0 0.00 16000.
~212.26.18.41 0.0.0.0 16 - 1024 0 0.0 0.00 16000.
* master (synced), # master (unsynced), + selected, - candidate, ~ configured
VG-KC#
VG-KC#sh vers
Cisco IOS Software, 2801 Software (C2801-IPVOICEK9-M), Version 12.4(21a), RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Mon 29-Sep-08 16:30 by prod_rel_team
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
VG-KC uptime is 1 day, 22 hours, 52 minutes
System returned to ROM by reload at 04:35:19 kuwaitz Fri Oct 4 2013
System restarted at 16:42:12 kuwaitz Fri Oct 4 2013
System image file is "flash:c2801-ipvoicek9-mz.124-21a.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco 2801 (revision 7.0) with 233472K/28672K bytes of memory.
Processor board ID FCZ125391FT
2 FastEthernet interfaces
8 Voice FXO interfaces
3 DSPs, 48 Voice resources
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
10-06-2013 05:46 AM
Hi,
In the output you can see that the NTP servers(212.26.18.43 & 212.26.18.41 ) have stratum value of 16.
Any stratum number that is above 15 is considered as unsynchronized.
VG-KC#sh ntp associations
address ref clock st when poll reach delay offset disp
*~127.127.7.1 127.127.7.1 4 36 64 377 0.0 0.00 0.0
~212.26.18.43 0.0.0.0 16 - 64 0 0.0 0.00 16000.
~212.26.18.41 0.0.0.0 16 - 1024 0 0.0 0.00 16000.
If these ntp servers are within your network then you can change the stratum values between 1- 15.
also you can refer this document.
https://supportforums.cisco.com/docs/DOC-1263
Regards,
Piyush Jain
Please rate helpful posts.
10-06-2013 06:21 AM
Hi,
did you configure the router as ntp server or you need to associate the router with ntp reference ?
212.26.18.43 0.0.0.0 16 - 64 0 0.0 0.00 16000.
~212.26.18.41 0.0.0.0 16 - 1024 0 0.0 0.00 16000.
are not accessible ?
HTH
Anas
please rate all helpful posts
10-06-2013 06:50 AM
Dear Anas
i configured as following :
clock timezone myzone +3 0
clock set xx:xx:xx 30 dec 2013
ntp master 5
there is some missing ?
10-06-2013 08:12 AM
Hello
Based on your configuration , you missed to configure ntp server.you have to use the below commands
ntp server 212.26.18.43
clock timezone myzone +3
ntp master 5
ntp source loopback 0 if you take a reference for ntp , select loopback as stable interface.If you have other routers you can use it.
can you share wit us , if your ntp will be used for CME or CUCM?.
Thank you
please rate all useful information
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide