cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1352
Views
5
Helpful
2
Replies

Outbound not hitting the correct/longest matched dial-peer

CODNetadmin
Level 1
Level 1

I do have 2 dial-peers, the scenario and configuration is here.

 

dial-peer voice 11 pots
description T6000 to ROW (US)
destination-pattern 0011T
progress_ind setup enable 3
progress_ind progress enable 8
translate-outgoing called 8842001
port 3/0:D
forward-digits all
!

dial-peer voice 1001345 pots
description T6000 to ROW (Cayman Islands)
destination-pattern 0011345T
progress_ind setup enable 3
progress_ind progress enable 8
translate-outgoing called 8842001
!

 

When I dialed "0011345T" Calls always hit the US Dial Peer (11).

I tried showing the dial plan, only the US Dial Peer shows up.

 

voice#show dialplan number 0011345 timeout
Macro Exp.: 0011345

VoiceEncapPeer11
peer type = voice, information type = voice,
description = `T6000 to ROW (US)',
tag = 11, destination-pattern = `0011T',
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
CLID Override RDNIS = disabled,
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 11, Admin state is up, Operation state is up,
Outbound state is up,
incoming called-number = `', connections/maximum = 0/unlimited,
DTMF Relay = disabled,
URI classes:
Destination =
huntstop = disabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):
Translation profile (Outgoing):
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
advertise 0x40 capacity_update_timer 25 addrFamily 4 oldAddrFamily 4
type = pots, prefix = `',
forward-digits all
session-target = `', voice-port = `3/0:D',
direct-inward-dial = disabled,
digit_strip = enabled,
register E.164 number with H323 GK and/or SIP Registrar = TRUE
fax rate = system, payload size = 20 bytes
supported-language = ''

Time elapsed since last clearing of voice call statistics never
Connect Time = 3427550, Charged Units = 0,
Successful Calls = 84, Failed Calls = 140, Incomplete Calls = 1
Accepted Calls = 0, Refused Calls = 0,
Last Disconnect Cause is "10 ",
Last Disconnect Text is "normal call clearing (16)",
Last Setup Time = 421421030.

 

No other dial peer shows on the dialplan even though it should check on the longest matched digit right?

1 Accepted Solution

Accepted Solutions

Georgios Fotiadis
VIP Alumni
VIP Alumni

Dial-peer 501 is missing the port x/x command, so it should be state down. You can verify by:

show dial-peer voice summary 

That is why you do not see a match about it.

Georgios
Please rate if you find this helpful.

View solution in original post

2 Replies 2

Georgios Fotiadis
VIP Alumni
VIP Alumni

Dial-peer 501 is missing the port x/x command, so it should be state down. You can verify by:

show dial-peer voice summary 

That is why you do not see a match about it.

Georgios
Please rate if you find this helpful.

Ohh that's why. Great!  Thank you so much!

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: