08-21-2013 11:16 PM - edited 03-16-2019 06:59 PM
Hi there, we have two h323 gateways confiugued with overlapping dial-pattern point to it. one working, but another not, debug isdn show following.
CUCM version 8.6.2.21900-5. Router CiSCO 2901 and IOS c2900-universalk9-mz.SPA.151-4.M4.bin.
Seem to me on the working router, the rest digits has been collected digit by digit, but on the not working one, the rest digits is not ignored. Any comments are welcome. Roy
Debug from working router:
Aug 22 05:32:59.218: ISDN Se0/1/0:15 Q931: TX -> SETUP pd = 8 callref = 0x2D29
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9839A
Exclusive, Channel 26
Calling Party Number i = 0x0081, '61298886290'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '0011656778' <<<<<<<<<<<<<<<<<<<<<<<<<
Plan:Unknown, Type:Unknown
XXXX-VCGW#
Aug 22 05:32:59.278: ISDN Se0/1/0:15 Q931: RX <- SETUP_ACK pd = 8 callref = 0xAD29
Channel ID i = 0xA9839A
Exclusive, Channel 26
Aug 22 05:32:59.518: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Called num 2 <<<<<<<<<<<<<<<<<
Aug 22 05:32:59.518: ISDN Se0/1/0:15 Q931: TX -> INFORMATION pd = 8 callref = 0x2D29
Called Party Number i = 0x81, '2'
Plan:ISDN, Type:Unknown
Aug 22 05:32:59.862: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Called num 3 <<<<<<<<<<<<<<<<<<
Debug form no working router:
Aug 22 2013 13:29:48.670 WST: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x2453
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9838A
Exclusive, Channel 10
Calling Party Number i = 0x0081, '61298886290'
XXXXX-vgw01#
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '0011656778' <<<<<<<<<<<<<<
Plan:Unknown, Type:Unknown
Aug 22 2013 13:29:48.734 WST: ISDN Se0/0/0:15 Q931: RX <- SETUP_ACK pd = 8 callref = 0xA453
Channel ID i = 0xA9838A
Exclusive, Channel 10
XXXXX-vgw01#
Aug 22 2013 13:29:53.086 WST: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x2453
Cause i = 0x8090 - Normal call clearing
Aug 22 2013 13:29:54.082 WST: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8 callref = 0xA453
Aug 22 2013 13:29:54.082 WST: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x2453
some commands used in router related to the h323 overlap:
voice service voip
h323
h245 signal overlap
voice call disc-pi-off
voice call send-alert
08-21-2013 11:36 PM
Mate, we need a bit more info here, both debugs show the same calling and called number I am not sure what and why you are using the overlap signal command.
shoot us the configs on both gateways and also Is the problem typical to certain dialed numbers or is it happening to all outbound calls?
Cheers
=============================
Please remember to rate useful posts, by clicking on the stars below.
=============================
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide