cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2589
Views
0
Helpful
7
Replies

Phones Stuck at Registering CME 10.5

yamikani2g2
Level 1
Level 1

Good day Experts.

 

I was failing to get remote access to the CME router i decided to remove the aaa configurations on the router.

I went on to have remote access as i only left this on the router...

aaa authentication login aaa_local local

 

When i checked all phoes are not registering they are stuck at "registering"

Can you walk me through making sure my phones are registered.

 

Thanks

7 Replies 7

M02@rt37
VIP
VIP

 Hi @yamikani2g2

 

Do you use sccp or sip control?

Please share your cme config too.

Best regards
.ı|ı.ı|ı. If This Helps, Please Rate .ı|ı.ı|ı.

I will share my configs but what i notice is that my phones where prevously getting IP addresses in the 10.0.X.X range now they are getting IP address in 192.168.0.X Range

 

I feel the network has a rogue DHCP server one other thing is that both data and Voice are in the same IP subnet range i really dont know why someone would do that. Best practise is to seperate the two.

 

But if we could resolve the current issue now i would be happy.. This seems to have disturbed 2 more branches that i have. I dont know what IP addresses the Branches are getting as they have non Cisco Phones. I am using SIP.

Ok @yamikani2g2

 

You perhaps find something wrong with dhcp server.

 

Ok for sip control.

Don't forget to configure ip address trusted list if your LAN-voip is unknown from your CME. Sometimes dhcp server is not on CME but on a remote router....then CME is blind about the remote sip phone LAN.

Best regards
.ı|ı.ı|ı. If This Helps, Please Rate .ı|ı.ı|ı.

R0g22
Cisco Employee
Cisco Employee
When you say remote, is it VPN ? If not, are these SIP phones and in a different subnet than your CME ?

Experts i sincerely apologize it was a physical issue. Cable not properly plugging in My appologies I started from physical before going to layer 3.

 

Thanks for solutions and insights..

Ok @yamikani2g2

 

Nevermind. You have found the problem :)

Best regards
.ı|ı.ı|ı. If This Helps, Please Rate .ı|ı.ı|ı.

Hi friend. I have this issue:

 

Phone keep in tftp process:

 

Oct 29 04:56:26.755: TFTP: Server request for port 51789, socket_id 0x7F84BD183A40 for process 3
Oct 29 04:56:26.755: TFTP: read request from host 192.168.50.2(51789) via GigabitEthernet0/0/0.11
Oct 29 04:56:26.755: TFTP: Looking for SEPD4AD71FB4CA0.cnf.xml
Oct 29 04:56:26.762: TFTP: Opened flash:/its/SEPD4AD71FB4CA0.cnf.xml, fd 10, size 5219 for process 3
Oct 29 04:56:26.762: TFTP: Sending block 1 (retry 0), len 512, socket_id 0x7F84BD183A40
Oct 29 04:56:26.763: TFTP: Received ACK for block 1, socket_id 0x7F84BD183A40
Oct 29 04:56:26.763: TFTP: Sending block 2 (retry 0), len 512, socket_id 0x7F84BD183A40
Oct 29 04:56:26.763: TFTP: Received ACK for block 2, socket_id 0x7F84BD183A40
Oct 29 04:56:26.764: TFTP: Sending block 3 (retry 0), len 512, socket_id 0x7F84BD183A40
Oct 29 04:56:26.764: TFTP: Received ACK for block 3, socket_id 0x7F84BD183A40
Oct 29 04:56:26.764: TFTP: Sending block 4 (retry 0), len 512, socket_id 0x7F84BD183A40
Oct 29 04:56:26.765: TFTP: Received ACK for block 4, socket_id 0x7F84BD183A40
Oct 29 04:56:26.765: TFTP: Sending block 5 (retry 0), len 512, socket_id 0x7F84BD183A40
Oct 29 04:56:26.765: TFTP: Received ACK for block 5, socket_id 0x7F84BD183A40
Oct 29 04:56:26.765: TFTP: Sending block 6 (retry 0), len 512, socket_id 0x7F84BD183A40
Oct 29 04:56:26.766: TFTP: Received ACK for block 6, socket_id 0x7F84BD183A40
Oct 29 04:56:26.766: TFTP: Sending block 7 (retry 0), len 512, socket_id 0x7F84BD183A40
Oct 29 04:56:26.766: TFTP: Received ACK for block 7, socket_id 0x7F84BD183A40
Oct 29 04:56:26.766: TFTP: Sending block 8 (retry 0), len 512, socket_id 0x7F84BD183A40
Oct 29 04:56:26.767: TFTP: Received ACK for block 8, socket_id 0x7F84BD183A40
Oct 29 04:56:26.767: TFTP: Sending block 9 (retry 0), len 512, socket_id 0x7F84BD183A40
Oct 29 04:56:26.767: TFTP: Received ACK for block 9, socket_id 0x7F84BD183A40
Oct 29 04:56:26.767: TFTP: Sending block 10 (retry 0), len 512, socket_id 0x7F84BD183A40
Oct 29 04:56:26.768: TFTP: Received ACK for block 10, socket_id 0x7F84BD183A40
Oct 29 04:56:26.768: TFTP: Sending block 11 (retry 0), len 99, socket_id 0x7F84BD183A40
Oct 29 04:56:26.769: TFTP: Received ACK for block 11, socket_id 0x7F84BD183A40
Oct 29 04:56:26.769: TFTP: Finished flash:/its/SEPD4AD71FB4CA0.cnf.xml, time 00:00:00 for process 3
Oct 29 04:56:30.235: TFTP: Server request for port 52868, socket_id 0x7F84BD183A40 for process 3
Oct 29 04:56:30.235: TFTP: read request from host 192.168.50.2(52868) via GigabitEthernet0/0/0.11
Oct 29 04:56:30.235: TFTP: Looking for SIP_English_United_States/sl-bev-sip.jar
Oct 29 04:56:30.235: TFTP: Sending error 1 No such file
Oct 29 04:56:31.235: TFTP: Server request for port 53165, socket_id 0x7F84BD183A40 for process 3
Oct 29 04:56:31.235: TFTP: read request from host 192.168.50.2(53165) via GigabitEthernet0/0/0.11
Oct 29 04:56:31.235: TFTP: Looking for United_States/g3-tones.xml
Oct 29 04:56:31.235: TFTP: Sending error 1 No such file

 

 

 

I see that open and finished file but not registering.

 

Also, I don´t see any request registration from phone:

 

Register pool 1 statistics
Active registrations : 0

Total SIP phones registered: 0
Total Registration Statistics
Registration requests : 0
Registration success : 0
Registration failed : 0
unRegister requests : 0
unRegister success : 0
unRegister failed : 0
Attempts to register
after last unregister : 0
Last register request time :
Last unregister request time :
Register success time :
Unregister success time :

 

 

Any ideas?? I have tested everything.

 

Before a reset of switch were working.

 

Help please.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: