cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
677
Views
0
Helpful
7
Replies

Register 887VA-V's FXS as SCCP to CUCM 9.1

dwtcp
Beginner
Beginner

Hi all,

i don't know if it is so obvious but i really can't find a solution!

And i can't find enough discussions so that means that i am completely wrong or nobody has tried it before.

I can see that my CUCM 9.1 offers 887VA-V subscription as SCCP gateway subscription.

Also, it offers a module VWIC-SLOT and then ports 0/0/0 through 0/0/3.

Therefore, if i enter the last 10digits of my 887s SCCP source interface mac-address, it creates a Device: AN1234567890000 through AN1234567890003

BUT,

my 887's config, which has fxs port 3 to 6 produces devices with names:

AN1234567890080 to AN1234567890083!!

What am i doing wrong.

Please advise:

IOS:c880voice-universalk9-mz.151-4.M4.bin

CUCM: 9.1.2(X)

 

1 Accepted Solution

Accepted Solutions

I was aware of the same but I though of sharing so that if u could get some clue.

If the problem is there, please open the case and share findings.

regds,

aman

View solution in original post

7 Replies 7

Hi.

Can you please share the output of a show voice port summary?

 

Thanks

 

Regards

 

Carlo

 

Please rate all helpful posts "The more you help the more you learn"

Hi Carlo,

here is the output:

vgw-r1#show voice port summary
                                           IN       OUT
PORT            CH   SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
=============== == ============ ===== ==== ======== ======== ==
1               1   bri-voice   up    dorm none     none     y
1               2   bri-voice   up    dorm none     none     y
2               1   bri-voice   up    dorm none     none     y
2               2   bri-voice   up    dorm none     none     y
3               --  fxs-ls      up    dorm on-hook  idle     y
4               --  fxs-ls      up    dorm on-hook  idle     y
5               --  fxs-ls      up    dorm on-hook  idle     y
6               --  fxs-ls      up    dorm on-hook  idle     y
50/0/1          1      efxs     up    up   on-hook  idle     y
50/0/2          1      efxs     up    up   on-hook  idle     y
50/0/3          1      efxs     up    up   on-hook  idle     y
50/0/4          1      efxs     up    up   on-hook  idle     y
50/0/5          1      efxs     up    up   on-hook  idle     y
50/0/6          1      efxs     up    up   on-hook  idle     y
50/0/7          1      efxs     up    up   on-hook  idle     y
50/0/8          1      efxs     up    up   on-hook  idle     y
50/0/9          1      efxs     up    up   on-hook  idle     y
50/0/10         1      efxs     up    up   on-hook  idle     y
 
PWR FAILOVER PORT        PSTN FAILOVER PORT
=================        ==================

 

Not sure, if this biug is somewhat related to your issue.

 

CCMGW page7.1 says fxs 0/0/0-3 port instead of GW voice-port 0-3
CSCta03837
 

Hi Aman,

this bug refers to MGCP configuration.

For SCCP, i choose the same about subunit but it CUCM creates 4 ports named:

0/0/0, 0/0/01, 0/0/2 and 0/0/3.

 This means that the last 3 digits of the SCCP device that CUCM creates (and cannot be altered) are 000 to 003.

But, as i told you in my previous email, port 3 in 887VA-V is created with 080 suffix (and port with 083 suffix)!

vgw-r1#show stcapp device summary
Total Devices:           2
Total Calls in Progress: 0
Total Call Legs in Use:  0

Port       Device          Device   Call          Dev     Directory   Dev
Identifier Name            State    State         Type    Number      Cntl
---------- --------------- -------- ------------- ------- ----------- ----
0/1/0      AN542DEA5DF6080 OOS      UNREGISTERED  ALG                 UNKN
0/1/3      AN542DEA5DF6083 OOS      UNREGISTERED  ALG                 UNKN
vgw-r1#show voice port summary
                                           IN       OUT
PORT            CH   SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
=============== == ============ ===== ==== ======== ======== ==
1               1   bri-voice   up    dorm none     none     y
1               2   bri-voice   up    dorm none     none     y
2               1   bri-voice   up    dorm none     none     y
2               2   bri-voice   up    dorm none     none     y
3               --  fxs-ls      up    dorm on-hook  idle     y
4               --  fxs-ls      up    dorm on-hook  idle     y
5               --  fxs-ls      up    dorm on-hook  idle     y
6               --  fxs-ls      up    dorm on-hook  idle     y
50/0/1          1      efxs     up    up   on-hook  idle     y
50/0/2          1      efxs     up    up   on-hook  idle     y
50/0/3          1      efxs     up    up   on-hook  idle     y
50/0/4          1      efxs     up    up   on-hook  idle     y
50/0/5          1      efxs     up    up   on-hook  idle     y
50/0/6          1      efxs     up    up   on-hook  idle     y
50/0/7          1      efxs     up    up   on-hook  idle     y
50/0/8          1      efxs     up    up   on-hook  idle     y
50/0/9          1      efxs     up    up   on-hook  idle     y
50/0/10         1      efxs     up    up   on-hook  idle     y
 
PWR FAILOVER PORT        PSTN FAILOVER PORT
=================        ==================

vgw-r1#

Cheers,

Anthony

I was aware of the same but I though of sharing so that if u could get some clue.

If the problem is there, please open the case and share findings.

regds,

aman

thanks for updates.

 

can u please share output of command show stcapp device summary and snapdhot from CUCM?

 

regds,

aman

dwtcp
Beginner
Beginner

Hi all,

it is a known bug with id CSCul59124 similar to the one regarding MGCP registration.

DO NOT add 887VA-V as 887VA-V but as 881/886/887.

Then, add FXS in subunit 1 and not 0.

This action, creates an analog device with suffix in the range 080-083.

 

Anthony

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers