Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
HI, we have project requirement to integrate the Iridium Satellite phone integration with Cisco PABX to make a calls in case of emergency. Can you please suggest, what can we achieved with this interface.1) can we make calls on any number at cisco PA...
Our old work phones would take turns around the room. I don't think it was called hunt group, but once logged in to your group/extension...it would go around the room on whose turn it was to answer. Is there a way to do that? Thanks
Does anyone know of a Cisco VOIP phone that supports direct fiber connection from phone to switch?
Hey,I have a CUCM 12.5 install that is running on evaluation. Whenever I place a call from one internal phone to a different one, hold music works just fine with my announcements and everything. But as soon as I place a call from the PSTN it just goe...
I have a DID I need to route to three different groups, receptionists during the day, medical staff for the evening, and an answering service after hours.The only option I can think of that has a schedule associated with it is a System Call Handler a...
Hi everyone! We have a problem with a call transfer.The structure is simple: My part ((Voip Tlf---->CUCM---->SBC))---->their part---((SBC---->CUCM---->TLF VOIPWhen we transfer an internal call (between 2 phones registered in our CUCM) there isn´t any...
Why do some of my calls get sent to Cisco Unity messaging system default mailbox instead of my personal mailbox?
Dears.I Have Avaya K175 configured as SIP on Cisco Call Manager.the phone keeps disconnecting every 2- 3 minutes.I can make calls from Avaya phone to Cisco phones. but Avaya is not receiving from Cisco " gives busy tone".I checked Cisco & Avaya logs ...
There may not be a "Best" strategy for adding a 9 when dialing out.I want to set up a fax machine so that any time the user sends a fax, they don't have to dial a "9"I thought I read that PLAR could do this in a Translation Pattern.I'm having trouble...
I’m trying to deploy a DECT IP network using Cisco Unified Communications Manager (CUCM).“CUCM” is essentially just a Cisco PBX and “DECT” is just a protocol for handsets to communicate with base stations.I think I found a limitation in CUCM.Basicall...
Dear Members,I have a Vodafone UK Landline; I was able to successfully configure it on Grand Stream HT812. When I use an analogue phone, everything works perfectly. Inbound & Outbound calling works, and also the caller ID is working perfectly. Now, W...
Hello, guys. I have a problem on my 4321 router. When I try to configure a sip ua, i've got a message: %Parse_RC-4_PRC-NON_COMPLIANCE:credentialsXXXXXXX username YYYYYYY realm ZZZZZ so, I can't see any outbound traffic to my SIP ISP and there is n...
We have SolarWinds monitoring solution in our environment. I was trying to configure SIP trunk session monitoring on SolarWinds VNQM, however I did not see any SIP trunks populated in SolarWinds. I opened a ticket with SolarWinds and they did postman...
My setup is as follows: CUCM -> CUBE -> ( Cisco Meraki MX400) -> ITSP. CUBE is behind NAT. Meraki does not support SIP NAT ALG. ITSP sees private IP in headers as the IP to send audio to despite 1:1 NAT mapping on firewall. How do I get the CUBE ...
Please is there a way I can register a 6851 3pcc to cucm We use cucm and have more than 200 6900 8800 and 9971 registered to it But then we also have a lot of 6851 3pcc which were mistakenly bought some years ago Is there a way we can register them t...
