cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
6947
Views
26
Helpful
20
Replies

Single Number Reach (SNR) remote Destination, Problem

Hi,

After configure the SNR, a guy (John) call the ip-phone (with its internal and external number), my cell phone rings, I answer, the cell is stalled.

But the call between the John's phone and my cell John is not connected, in the John's phone, you always hear the bells, as if nobody had yet won.

if i test with a call forwarding (forward all or no answer), it's good, no problem

Who have a idea?

It's a french intallation BRI.

CUCM v9.1 (BE6000)

c2901 v15.4(1)T (i have test with 15.3 and 15.2 version)

no error message in the router's debug q931 when in test SNR

Routeur-CUCM#
Dec 22 16:31:20.660: ISDN BR0/0/1 Q931: RX <- SETUP pd = 8  callref = 0x75
        Bearer Capability i = 0x8090A3
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0x89
                Exclusive, B1
        Calling Party Number i = 0x2183, 'JOHN PHONE'
                Plan:ISDN, Type:National
        Called Party Number i = 0xA1, 'External number IP-PHONE'
                Plan:ISDN, Type:National
        Sending Complete
Dec 22 16:31:20.680: ISDN BR0/0/1 Q931: TX -> CALL_PROC pd = 8  callref = 0xF5
        Channel ID i = 0x89
                Exclusive, B1
Dec 22 16:31:20.692: ISDN BR0/0/1 Q931: TX -> ALERTING pd = 8  callref = 0xF5
        Progress Ind i = 0x8088 - In-band info or appropriate now available
Dec 22 16:31:24.700: ISDN BR0/0/0 Q931: TX -> SETUP pd = 8  callref = 0x77
        Sending Complete
        Bearer Capability i = 0x8090A3
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0x8A
                Exclusive, B2
        Calling Party Number i = 0x2183, 'External number IP-PHONE'

                Plan:ISDN, Type:National
        Called Party Number i = 0x80, 'My CELL PHONE number'
                Plan:Unknown, Type:Unknown
        Redirecting Number i = 0x00008F, '117'
                Plan:Unknown, Type:Unknown
Dec 22 16:31:24.768: ISDN BR0/0/0 Q931: RX <- CALL_PROC pd = 8  callref = 0xF7
        Channel ID i = 0x8A
                Exclusive, B2
Dec 22 16:31:29.804: ISDN BR0/0/0 Q931: RX <- ALERTING pd = 8  callref = 0xF7
        Channel ID i = 0x8A
                Exclusive, B2
        Progress Ind i = 0x8088 - In-band info or appropriate now available
Dec 22 16:31:31.984: ISDN BR0/0/0 Q931: RX <- CONNECT pd = 8  callref = 0xF7
        Channel ID i = 0x8A
                Exclusive, B2
        Facility i = 0x91A306020100020103
                Protocol Profile = Remote Operations Protocol
                0xA306020100020103
                Component = Return Error component
                        Invoke Id = 0

                        Error = 3 not available

20 Replies 20

Manish Prasad
Level 5
Level 5

It seems to be configuration issue with SNR.

Check this document- https://supportforums.cisco.com/docs/DOC-27111

Thanks

Manish

Thanks, i used this document for to check my configuration, but it does not solves my problem.

My SNR "works", the cell ring, but when i answer, the communication is not connected with John (external phone) and my cell, as if the CUCM did not see that the cell has answered.

I use a MGCP gateway, it's possible to just use the the SNR feature with this gateway's type?

Or it's requires a H323 gateway?

Hi, no idea for me?

I don't use the MVA, and for the MVA I know it takes a H323 gateway.

I tested with a trunk sip link and it's ok, SNR work.

It's possible to use the SNR with a MGCP gateway?

I have check with this document, but no succes for use with my MGCP gateway.

https://supportforums.cisco.com/docs/DOC-27111

Can you help me please?

Thanks.

HI Gilles.

Can you please attach a screenshot of both Remote Destination and Remote Destination Profile pages.

Thanks

Carlo

Please rate all helpful posts

"The more you help the more you learn"

Please rate all helpful posts "The more you help the more you learn"

Hi Carlo, you can see my screenshot of both Remote Destination and Remote Destination Profile pages in the attached file.

Thanks

Hi Gilles

Can you try to put Answer Too Soon timer to 500 instead of 1500 and send a deb isd q931 from your gateway?

Thanks

Regards

Carlo

Please rate all helpful posts

"The more you help the more you learn"

Please rate all helpful posts "The more you help the more you learn"

Hi Carlo,

It's the same problème with "Answer Too Soon timer to 500", but i tested with H323 gateway and Trunk Sip and it's ok, but no with MGCP gateway :-(

Gateway-MGCP#debug isdn q931

debug isdn q931 is              ON.

Gateway-MGCP#

*Jan  9 17:31:47.135: ISDN BR0/0/0 Q931: RX <- SETUP pd = 8  callref = 0x0D

        Sending Complete

        Bearer Capability i = 0x9090A3

                Standard = CCITT

                Transfer Capability = 3.1kHz Audio

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0x89

                Exclusive, B1

        Calling Party Number i = 0x2083, '296622525'

                Plan:Unknown, Type:National

        Called Party Number i = 0x81, '1228'

                Plan:ISDN, Type:Unknown

*Jan  9 17:31:47.167: ISDN BR0/0/0 Q931: TX -> CALL_PROC pd = 8  callref = 0x8D

        Channel ID i = 0x89

                Exclusive, B1

*Jan  9 17:31:47.191: ISDN BR0/0/0 Q931: TX -> ALERTING pd = 8  callref = 0x8D

        Progress Ind i = 0x8088 - In-band info or appropriate now available

*Jan  9 17:31:51.191: ISDN BR0/0/0 Q931: TX -> SETUP pd = 8  callref = 0x04

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0x8A

                Exclusive, B2

        Calling Party Number i = 0x2083, '0296642525'

                Plan:Unknown, Type:National

        Called Party Number i = 0x80, '0290035006'

                Plan:Unknown, Type:Unknown

        Redirecting Number i = 0x00008F, '2001'

                Plan:Unknown, Type:Unknown

*Jan  9 17:31:51.563: ISDN BR0/0/0 Q931: RX <- CALL_PROC pd = 8  callref = 0x84

        Channel ID i = 0x8A

                Exclusive, B2

*Jan  9 17:31:52.415: ISDN BR0/0/0 Q931: RX <- ALERTING pd = 8  callref = 0x84

*Jan  9 17:31:52.967: ISDN BR0/0/0 Q931: RX <- PROGRESS pd = 8  callref = 0x84

        Cause i = 0x87F2 - Unknown cause value

        Progress Ind i = 0x8281 - Call not end-to-end ISDN, may have in-band info

*Jan  9 17:31:55.127: ISDN BR0/0/0 Q931: RX <- CONNECT pd = 8  callref = 0x84

*Jan  9 17:32:02.123: ISDN BR0/0/0 Q931: RX <- DISCONNECT pd = 8  callref = 0x84

        Cause i = 0x8790 - Normal call clearing

*Jan  9 17:32:02.619: ISDN BR0/0/0 Q931: RX <- RELEASE pd = 8  callref = 0x0D

        Cause i = 0x8790 - Normal call clearing

*Jan  9 17:32:02.623: ISDN BR0/0/0 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x8D

        Info Request i = 0x80

*Jan  9 17:32:32.179: ISDN BR0/0/0 Q931: RX <- RELEASE pd = 8  callref = 0x84

        Cause i = 0x8790 - Normal call clearing

*Jan  9 17:32:32.183: ISDN BR0/0/0 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x04

        Info Request i = 0x80

*Jan  9 17:32:34.271: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR0/0/0, TEI 0 changed to down

*Jan  9 17:32:34.299: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0/0/0, TEI 0 changed to up

I think if its a MGCP gateway then might need to re-route the call back to H.323 gw and back to CUCM. having said if its only mgcp gw in the call flow then it won't work.


Br,
Nadeem 

Please rate all useful post.

Br, Nadeem Please rate all useful post.

Hi Gilles.
To be honest I always preferred SIP or H323 as signaling protocol.
Tomorrow I'll setup a LAB to test MGCP with SNR and I'll let you know



Regards

Carlo

Sent from Cisco Technical Support iPhone App

Please rate all helpful posts "The more you help the more you learn"

ok Carlo, thank you very much for your help.

Good morning Gilles.

I reproduded SNR configuration in my lab with mgcp gateway.

Adjusting following timers, all worked good.

Answer Too Soon Timer: 500

Answer Too Late Timer: 30000

Delay Before Ringing Timer:1000

Try this settings and let me know

Regards

Carlo

Please rate all helpful posts

"The more you help the more you learn"

Please rate all helpful posts "The more you help the more you learn"

i have the same problem with this timers.

Gilles,

Please collect a debbug isdn  q931 during these 3 situations

1) direct call to your mobile from an ip phone

2) forward your extension to your mobile and call your extension from another ip phone

3) From an ip phone, call your extensions removing call forward settings.

Thanks

Carlo

Please rate all helpful posts

"The more you help the more you learn"

Please rate all helpful posts "The more you help the more you learn"
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: