cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
8154
Views
10
Helpful
10
Replies

SIP Trunk Between CUCM and Asterisk

kennedymacharia
Level 1
Level 1

Hi All,

I have a trunk between cucm 11 and asterisk but when a call is made from asterisk to cucm it disconnects immediately it is picked. Any idea?

1 Accepted Solution

Accepted Solutions

Hi,

The issue you are having is the region config between the asterisk SIP trunk and cisco phones.

The region config is set to use 8kbps ( region default to JubileeTZ).  Your Asterisk server is only advertising G711, hence a xcoder is needed. Please change the region setting to use 64Kbps

 

++ CUCM logs +++

35738374.006 |09:32:08.637 |AppInfo  |DET-MediaManager-(166857)::preCheckCapabilities, region1=Default, region2=JubileeTZ, Pty1 capCount=2 (Cap,ptime)= (2,20) (4,20), Pty2 capCount=9 (Cap,ptime)= (90,20) (6,20) (4,20) (2,20) (86,20) (11,20) (12,20) (15,20) (16,20)
35738374.007 |09:32:08.637 |AppInfo  |DET-RegionsServer::matchCapabilities-- savedOption=0, PREF_NONE, regionA=(null) regionB=(null) latentCaps(A=0, B=0) kbps=8, capACount=2, capBCount=9
35738374.008 |09:32:08.637 |AppInfo  |RegionsServer: applyCodecFilterIfNeeded - no codecs remained after filtering so restored original 0 caps

---

35738374.009 |09:32:08.637 |AppInfo  |DET-MediaManager-(166857)::preCheckCapabilities, caps mismatch! Xcoder Reqd. kbps(8), filtered A[capCount=0 (Cap,ptime)=], B[capCount=5 (Cap,ptime)= (90,20) (11,20) (12,20) (15,20) (16,20)] allowMTP=0 numXcoderRequired=1 xcodingSide=1

 

++ CUCM tried to allocate a xcoder but didnt find any ++

 

5738376.003 |09:32:08.637 |AppInfo  |MRM::convertScmStringToStdString MRG-AmeyoQueue
35738376.004 |09:32:08.637 |AppInfo  |MRM::getXcodeDeviceGivenMrgl
35738376.005 |09:32:08.637 |AppInfo  |MRM::getXcodeDeviceGivenMrgl GETTING XCODE FROM DEFAULT LIST
35738376.006 |09:32:08.637 |AppInfo  |MediaResourceManager::sendAllocationResourceErr - ERROR - no transcoder device configured

Please rate all useful posts

View solution in original post

10 Replies 10

Ayodeji Okanlawon
VIP Alumni
VIP Alumni

That sounds like a media negotiation issue. We are going to need CUCM logs to know why. A couple of things to check. What is the codec that is advertised from Asterisk? What is the bit rate on the region that is configured between the SIP trunk and the endpoint in CUCM?

Please rate all useful posts

Hi,

Thanks for the reply. The logs are attached. The Asterisk IP is 10.5.10.6 and I am calling Extension 3015

Hi,

The issue you are having is the region config between the asterisk SIP trunk and cisco phones.

The region config is set to use 8kbps ( region default to JubileeTZ).  Your Asterisk server is only advertising G711, hence a xcoder is needed. Please change the region setting to use 64Kbps

 

++ CUCM logs +++

35738374.006 |09:32:08.637 |AppInfo  |DET-MediaManager-(166857)::preCheckCapabilities, region1=Default, region2=JubileeTZ, Pty1 capCount=2 (Cap,ptime)= (2,20) (4,20), Pty2 capCount=9 (Cap,ptime)= (90,20) (6,20) (4,20) (2,20) (86,20) (11,20) (12,20) (15,20) (16,20)
35738374.007 |09:32:08.637 |AppInfo  |DET-RegionsServer::matchCapabilities-- savedOption=0, PREF_NONE, regionA=(null) regionB=(null) latentCaps(A=0, B=0) kbps=8, capACount=2, capBCount=9
35738374.008 |09:32:08.637 |AppInfo  |RegionsServer: applyCodecFilterIfNeeded - no codecs remained after filtering so restored original 0 caps

---

35738374.009 |09:32:08.637 |AppInfo  |DET-MediaManager-(166857)::preCheckCapabilities, caps mismatch! Xcoder Reqd. kbps(8), filtered A[capCount=0 (Cap,ptime)=], B[capCount=5 (Cap,ptime)= (90,20) (11,20) (12,20) (15,20) (16,20)] allowMTP=0 numXcoderRequired=1 xcodingSide=1

 

++ CUCM tried to allocate a xcoder but didnt find any ++

 

5738376.003 |09:32:08.637 |AppInfo  |MRM::convertScmStringToStdString MRG-AmeyoQueue
35738376.004 |09:32:08.637 |AppInfo  |MRM::getXcodeDeviceGivenMrgl
35738376.005 |09:32:08.637 |AppInfo  |MRM::getXcodeDeviceGivenMrgl GETTING XCODE FROM DEFAULT LIST
35738376.006 |09:32:08.637 |AppInfo  |MediaResourceManager::sendAllocationResourceErr - ERROR - no transcoder device configured

Please rate all useful posts

Thanks man this fixed the issue. I could not see that. Thanks again

Ratheesh Kumar
VIP Alumni
VIP Alumni

Hi there

 

Can you post some debugs from the gateway here. Could you try the following,

 

  1. Assign a Hardware MTP to the call
  2. Assign software MTP to MRGL
  3. Check MTP required on CUCM SIP Trunk

 

Hope this helps!

Cheers
Rath!


***Please rate helpful posts***

hi,

I have already applied resources but the issue persist. I have attached some logs above

As Ayodeji suggested try changing the region setting between the IP Phones and SIP trunk to use 64kbps  ( to ensure that xcoder is not required ) and then test. If the issue persists then share the traces for one such failed call.

 

Manish

please enable SIP debug log in CUCM and collect SDL log then share it here

 

you might refer to this document

 

https://www.cisco.com/c/en/us/support/docs/unified-communications/unified-communications-manager-callmanager/200787-How-to-Collect-Traces-for-CUCM-9-x-10-x.html

 

 

has anyone figured out how to sip trunk connect asterisk to CUCM on a newer version by using pjsip.conf? 

if so, would you please share your config ? 

dsalazar
Level 1
Level 1

Yes, using cucm 11.5 and issabel pbx the trunk works bothways....   

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: