10-24-2015 01:46 PM - edited 03-17-2019 04:41 AM
A typical Setup message used to look like this:
Oct 24 20:31:10.044: ISDN Se0/0:23 Q931: TX -> SETUP pd = 8 callref = 0x0080
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Progress Ind i = 0x8583 - Origination address is non-ISDN
Calling Party Number i = 0x80, '9725900222'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '8303'
Plan:Unknown, Type:Unknown
Oct 24 20:31:10.072: ISDN Se0/0:23 Q931: RX <- CALL_PROC pd = 8 callref = 0x8080
Channel ID i = 0xA98381
Exclusive, Channel 1
In newer IOS 15.1(4)M9 the same message looks like this:
Oct 24 15:34:44.141: ISDN Se0/0/1:23 Q931: TX -> SETUP pd = 8 callref = 0x0081
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Progress Ind i = 0x8583 - Origination address is non-ISDN
Signal i = 0x40 - Alerting on - pattern 0
Calling Party Number i = 0x2180, '9725900222'
Plan:ISDN, Type:National
Called Party Number i = 0x80, '8306'
Plan:Unknown, Type:Unknown
Locking Shift to Codeset 5
Codeset 5 IE 0x41 i = 0xC4890000000000
Oct 24 15:34:44.153: ISDN Se0/0/1:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x8081
Cause i = 0x80E4 - Invalid information element contents
Differences are in red. Is there any way to take them out? My other ISDN device doesn't like this new Setup message.
Thank you!
10-24-2015 02:40 PM
Hi.
Can you please send your actual config?
Thanks
Carlo
10-24-2015 03:22 PM
10-24-2015 11:12 PM
Hi.
Maybe your provider does not accept Numbering plan "Unknown"
Try to set it to Subcriber or National modifying route pattern on cucm or applying a voice translation profile on dialpeer
Please let me know
Regards
Carlo
10-25-2015 01:21 AM
Hi Experts,
Greetings
I am calling from IP Phone to PSTN & called party is not answering my call, after some rings call is getting hangup and i am not able to hear hangup tone or beep, rather i am getting system recording like "your call can not be completed as dialed please console your directory"
Please advise me to remove the system recording & let me able to get beep tone after called party not answering call
Thanks in advance
Warm Regards:
Nabeel Asghar
10-26-2015 05:41 AM
Tried that idea, but didn't solve the problem. Please note the response I've got:
Invalid information element contents
10-26-2015 05:55 AM
Hi.
Please under voice-port 0/0/0:23 and 0/0/1:23 add "bearer-cap speech" and "command-type A-LAW"
Let me know
Regards
Carlo
10-29-2015 11:05 AM
Tried these suggestions, still no fix. Thank you.
10-30-2015 04:15 AM
Hi.
Please download 15.1.4M10 and upgrade your VG.
Let me know if it solves your issue.
HTH
Regards
Carlo
12-06-2016 04:48 AM
Hi, I have the same issue...
Were you able to fix it?
If yes, how please?
12-06-2016 06:08 AM
MLPP adds those messages. Turn MLPP off to remove those lines.
12-06-2016 06:21 AM
Effectively no voice mlpp fixes the issue! Many thanks.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: