cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
903
Views
10
Helpful
9
Replies

Trancoding on ISR2921

tkavithas87
Level 1
Level 1

I am trying to create trancoding on the 2921 router.

It has pvdm 3

when i create the  profile ,couldnt assign codec to the profile.what could be the cause?

2921(config)#dspfarm profile 1 transcode

2921(config-dspfarm-profile)#codec ?

% Unrecognized command

2 Accepted Solutions

Accepted Solutions

If you had a PVDM installed, your output of sh inventory would contain similar to below depending upon channels:

NAME: "PVDM3 DSP DIMM with 32 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 32 Channels"
PID: PVDM3-32 , VID: V01 , SN: FOCxxxx

Please let us know if you have further questions or please mark the thread answered.

Terry

Please rate useful posts.

Sent from Cisco Technical Support iPad App

View solution in original post

Harmit Singh
Cisco Employee
Cisco Employee

Hi Kavithas,

Terry is spot on (+5)! You should be able to see the PVDM module in the show inventory or show diag. If you're absolutely sure there should be a PVDM in there, then it's possible that the PVDM hasnt been seated into the PVDM slot properly or the slot has gone bad or the PVDM has gone bad. Assuming the PVDM is present, then pop open the chassis cover (powered down ofcourse) and try the other PVDM slot. If it gets detected, you know the PVDM is fine but the slot is bad.

HTH.


--
Regards,
Harmit.

View solution in original post

9 Replies 9

Terry Cheema
VIP Alumni
VIP Alumni

Can you post the output of -
sh inventory
sh ver | i IOS

It appears router isn't detecting pvdm

-Terry

Sent from Cisco Technical Support iPad App

2921#show inventory

NAME: "CISCO2921/K9", DESCR: "CISCO2921/K9 chassis, Hw Serial#: FGL1636147P, Hw                                                                                         Revision: 1.0"

PID: CISCO2921/K9      , VID: V07 , SN: FGL1636147P

NAME: "C2921/C2951 AC Power Supply", DESCR: "C2921/C2951 AC Power Supply"

PID: PWR-2921-51-AC    , VID: V03 , SN: DCA1633K1L0

2921#show version

Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.2(4)M2, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2012 by Cisco Systems, Inc.

Compiled Wed 07-Nov-12 14:08 by prod_rel_team

ROM: System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)

2921 uptime is 2 hours, 32 minutes

System returned to ROM by power-on

System restarted at 09:20:12 sg Sat Feb 23 2013

System image file is "flash:c2900-universalk9-mz.SPA.152-4.M2.bin"

Last reload type: Normal Reload

Last reload reason: power-on

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

Cisco CISCO2921/K9 (revision 1.0) with 487424K/36864K bytes of memory.

Processor board ID FGL1636147P

3 Gigabit Ethernet interfaces

1 terminal line

1 Virtual Private Network (VPN) Module

DRAM configuration is 64 bits wide with parity enabled.

255K bytes of non-volatile configuration memory.

250880K bytes of ATA System CompactFlash 0 (Read/Write)

License Info:

License UDI:

-------------------------------------------------

Device#   PID                   SN

-------------------------------------------------

*0        CISCO2921/K9          FGL1636147P

Technology Package License Information for Module:'c2900'

-----------------------------------------------------------------

Technology    Technology-package           Technology-package

              Current       Type           Next reboot

------------------------------------------------------------------

ipbase        ipbasek9      Permanent      ipbasek9

security      securityk9    Permanent      securityk9

uc            uck9          Permanent      uck9

data          None          None           None

Configuration register is 0x2102

2921#show run | s voice-card

voice-card 0

dsp services dspfarm

Based on the output of your sh inventory output either there is no PVDM installed or router is not detecting, you can try reseating if you have installed one.

Terry

Please rate all helpful posts.

Sent from Cisco Technical Support iPad App

If you had a PVDM installed, your output of sh inventory would contain similar to below depending upon channels:

NAME: "PVDM3 DSP DIMM with 32 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 32 Channels"
PID: PVDM3-32 , VID: V01 , SN: FOCxxxx

Please let us know if you have further questions or please mark the thread answered.

Terry

Please rate useful posts.

Sent from Cisco Technical Support iPad App

Harmit Singh
Cisco Employee
Cisco Employee

Hi Kavithas,

Terry is spot on (+5)! You should be able to see the PVDM module in the show inventory or show diag. If you're absolutely sure there should be a PVDM in there, then it's possible that the PVDM hasnt been seated into the PVDM slot properly or the slot has gone bad or the PVDM has gone bad. Assuming the PVDM is present, then pop open the chassis cover (powered down ofcourse) and try the other PVDM slot. If it gets detected, you know the PVDM is fine but the slot is bad.

HTH.


--
Regards,
Harmit.

Harmit - thanks for the nice rating buddy. +5 for your accurate post as well!

-Terry

Sent from Cisco Technical Support iPad App

yeah the PVDM is not slotted correctly.I have slotted correctly .its working now.thank you guys.

Not a problem mate - glad it resolved your issue!

- Terry

Sent from Cisco Technical Support iPad App

Glad to hear that, see you around! :-)


--
Regards,
Harmit.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: