cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
871
Views
0
Helpful
5
Replies

Translation pattern fails

ivan aguilar
Level 1
Level 1

Hi I have in a CUCM 8 a Translation-pattern to a internal extension, this fails and the debug shows ´Unallocated/unassigned number´

That extension is registered, and without any problem, i even test the TP with other extension, and fails again.

The call from CUCM to the remote site go through h323 trunk to a CME-SRST site.

ISDN channel are well, and outbound calls runs properly, this is the sh isdn status:

Global ISDN Switchtype = basic-net3

ISDN BRI0/0/0 interface

        dsl 0, interface ISDN Switchtype = basic-net3

    Layer 1 Status:

        ACTIVE

    Layer 2 Status:

        TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED

    Layer 3 Status:

        0 Active Layer 3 Call(s)

    Active dsl 0 CCBs = 0

    The Free Channel Mask:  0x80000003

ISDN BRI0/0/1 interface

        dsl 1, interface ISDN Switchtype = basic-net3

    Layer 1 Status:

        ACTIVE

    Layer 2 Status:

        TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED

    Layer 3 Status:

        0 Active Layer 3 Call(s)

    Active dsl 1 CCBs = 0

    The Free Channel Mask:  0x80000003

And the debug isdn q931

Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0x82

                Preferred, B2

        Calling Party Number i = 0x2183, '6xxxxxxxx'

                Plan:ISDN, Type:National

        Calling Party Number i = 0x0183, '6xxxxxxxx'

                Plan:ISDN, Type:Unknown

        Called Party Number i = 0xA1, '91xxxxxxx'

                Plan:ISDN, Type:National

*Aug 22 09:05:42.448: ISDN BR0/0/0 Q931: TX -> CALL_PROC pd = 8  callref = 0xB4

        Channel ID i = 0x8A

                Exclusive, B2

*Aug 22 09:05:42.464: ISDN BR0/0/0 Q931: TX -> DISCONNECT pd = 8  callref = 0xB4

        Cause i = 0x8081 - Unallocated/unassigned number

*Aug 22 09:05:42.620: ISDN BR0/0/0 Q931: RX <- RELEASE pd = 8  callref = 0x34

*Aug 22 09:05:42.620: ISDN BR0/0/0 Q931: TX -> RELEASE_COMP pd = 8  callref = 0xB4

I have other Translation-pattern to other extension but in other sites from cluster and all works fine, why this is failing?

The dial-peer are:

dial-peer voice 100 pots are (only put one for BRI)

dial-peer voice 1 pots

preference 1

destination-pattern 0T

port 0/0/0

!

dial-peer voice 20 pots

destination-pattern 06........

port 0/0/0

forward-digits 9

dial-peer voice 10 pots

preference 1

destination-pattern 09........

port 0/0/0

forward-digits 9

dial-peer voice 100 pots

incoming called-number .

direct-inward-dial

port 0/0/0

dial-peer voice 20 pots
destination-pattern 06........
port 0/0/0
forward-digits 9

!

dial-peer voice 10 pots
preference 1
destination-pattern 09........
port 0/0/0
forward-digits 9

!

dial-peer voice 100 pots
incoming called-number .
direct-inward-dial
port 0/0/0

Into CUCM/DNA show it runs, which could be the cause of this problem??

Thanks!!

1 Accepted Solution

Accepted Solutions