02-19-2021 02:53 PM
Dears
kindly need support , i cant configure voice ports in cisco 2811,
Router(config-dial-peer)#port ?
% Unrecognized command
Router(config-dial-peer)#port
and also ,
Router#show voice port summary
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
=============== == ============ ===== ==== ======== ======== ==
PWR FAILOVER PORT PSTN FAILOVER PORT
================= ==================
Router#
**************************
Router#sh version
Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 15.1(2)T2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Sat 23-Oct-10 00:10 by prod_rel_team
Router#sh inventory
NAME: "2811 chassis", DESCR: "2811 chassis"
PID: CISCO2811 , VID: V02 , SN: FCZ100271BE
NAME: "WAN Interface Card - T1E1 or ATM (With GSHDSL-F module) on Slot 0 SubSlot 0", DESCR: "WAN Interface Card - T1E1 or ATM (With GSHDSL-F module)"
PID: WIC-1SHDSL-V2 , VID: V02 , SN: FOC094236Z9
NAME: "WAN Interface Card - ATM (With multi line G.SHDSL module) on Slot 0 SubSlot 2", DESCR: "WAN Interface Card - ATM (With multi line G.SHDSL module)"
PID: WIC-1SHDSL-V3 , VID: V01 , SN: FOC102018GQ
NAME: "WAN Interface Card - ATM (With multi line G.SHDSL module) on Slot 0 SubSlot 3", DESCR: "WAN Interface Card - ATM (With multi line G.SHDSL module)"
PID: WIC-1SHDSL-V3 , VID: V01 , SN: FOC102018KM
NAME: "PVDMII DSP SIMM with four DSPs on Slot 0 SubSlot 5", DESCR: "PVDMII DSP SIMM with four DSPs"
PID: PVDM2-64 , VID: V01 , SN: FOC12492D1Z
NAME: "Two Port Channelized E1/T1/PRI with Integrated CSU on Slot 1", DESCR: "Two Port Channelized E1/T1/PRI with Integrated CSU"
PID: , VID: 1.0, SN: FOC10231J46
Router#show run
Building configuration...
Current configuration : 1366 bytes
!
! Last configuration change at 03:27:16 UTC Sat Feb 20 2021
!
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
card type e1 1
!
no aaa new-model
!
no network-clock-participate slot 1
!
dot11 syslog
ip source-route
!
!
ip cef
!
!
!
no ipv6 cef
!
multilink bundle-name authenticated
!
!
!
!
isdn switch-type primary-net5
!
!
!
!
!
!
!
voice-card 0
dspfarm
dsp services dspfarm
!
crypto pki token default removal timeout 0
!
!
!
!
license udi pid CISCO2811 sn FCZ100271BE
!
redundancy
!
!
controller DSL 0/0/0
!
controller DSL 0/2/0
!
controller DSL 0/3/0
!
controller E1 1/0
framing NO-CRC4
clock source internal
pri-group timeslots 1-31
!
controller E1 1/1
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
ip address 10.136.0.240 255.255.255.0
duplex auto
speed auto
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Serial1/0:15
no ip address
encapsulation hdlc
dialer-group 1
isdn switch-type primary-net5
no cdp enable
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
!
logging esm config
!
!
!
!
!
!
control-plane
!
!
!
!
!
dial-peer voice 1000 pots
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
transport input all
!
scheduler allocate 20000 1000
end
Solved! Go to Solution.
02-19-2021 03:56 PM
Since i see dialer-group 1 configured under interface Serial1/0:15 this is not used for voice and its for channelized data.
Since this is a bit old module, i believe those cards are for data and not for voice. AFAIk to support voice it should be VWIC card.
02-20-2021 09:40 AM
Hi Omar,
Unfortunately NM-2CE1T1-PRI is for data only not for Voice.
That's why you're unable to conficure voice-ports on this gateway.
For 28XX series routers Voice Modules part number starts with a V.
Eg VWIC2-2MFT-T1/E1 this card is a 2 ports ISDN -PRI supporting Voice.
HTH
Regards
Carlo
02-19-2021 03:56 PM
Since i see dialer-group 1 configured under interface Serial1/0:15 this is not used for voice and its for channelized data.
Since this is a bit old module, i believe those cards are for data and not for voice. AFAIk to support voice it should be VWIC card.
02-19-2021 11:10 PM
02-20-2021 12:10 AM
Dears
i tried a lot of different IOS like
c2800nm-ipvoicek9-mz.151-3.T
c2800nm-advipservicesk9-mz.151-2.T2
c2800nm-spservicesk9-mz.124-3f
all of the the same , no voice port command enabled
regarding to the module its called "NM-2CE1T1-PRI" .i think it works as ISDN PRI
very thanks
02-20-2021 01:09 AM
The command to configure a voice port is voice-port.
02-20-2021 04:28 AM
Dear Roger
thanks for your response , ya i know that the command for voice port is " voice-port " , but also this command is not found
Router(config)#voice?
voice voice-card
Router(config)#voice
Router(config)#voice-port?
% Unrecognized command
Router(config)#voice-port
as mentioned before this all info
version :- Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 15.1(1)T, RELEASE SOFTWARE (fc1)
E1 Module installed is :- "NM-2CE1T1-PRI"
PVDM2-64 installed and recognized
what i want is to configure voice E1 PRI Between router and PSTN network to enable voice calls to Asterisk PBX
the problems :-
1- i cant execute command " Voice-port "in config mode
2- i cant execute command " port" under dial-peer pots
3- no output listed when execute command show voice port summary
02-20-2021 09:40 AM
Hi Omar,
Unfortunately NM-2CE1T1-PRI is for data only not for Voice.
That's why you're unable to conficure voice-ports on this gateway.
For 28XX series routers Voice Modules part number starts with a V.
Eg VWIC2-2MFT-T1/E1 this card is a 2 ports ISDN -PRI supporting Voice.
HTH
Regards
Carlo
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: