cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1663
Views
0
Helpful
3
Replies

Unity Connection -- CME integration

nafrasiyabov
Level 1
Level 1

Hi people.

I have some issues when integration UC-CME via SCCP. Every thing works just fine except MWI lights do not work on SIP phones.

Here is the config from CME router:

voice service voip

allow-connections sip to sip

no supplementary-service sip moved-temporarily
sip
  bind control source-interface FastEthernet0/0.200
  bind media source-interface FastEthernet0/0.200
  registrar server expires max 600 min 60

!

!

voice register global
mode cme
source-address x.x.x.x( FastEthernet0/0.200) port 5060
max-dn 20
authenticate register

voicemail 4001
tftp-path flash:

!

voice register dn  1
number 3002
call-forward b2bua busy 4001 
call-forward b2bua noan 4001 timeout 7
allow watch
name BR2 Phone 2
mwi    

!

voice register pool  1
id mac XXXX.XXXX.XXXX
type 7970
number 1 dn 1
presence call-list
dtmf-relay sip-notify
username farmer password cisco
codec g711ulaw

!

!

sip-ua
mwi-server ipv4:y.y.y.y expires 3600 port 5060 transport tcp unsolicited

!

!

telephony-service

max-ephones 20

max-dn 20 no-reg

ip source-address x.x.x.x port 2000

voicemail 4001
max-conferences 8 gain -6
call-forward pattern .T

mwi relay

!

!

ephone-dn  1  octo-line
number 3001 no-reg primary
name BR2 phone 1
allow watch
call-forward busy 4001
call-forward noan 4001 timeout 9

!

ephone-dn  10  dual-line
number 4001
preference 1
huntstop channel
no huntstop
!                 
ephone-dn  11  dual-line
number 4001
preference 2
huntstop channel

!

ephone-dn  20 dual-line

number 8000 secondary 8001

mwi on-off

!

ephone  1
device-security-mode none
mac-address XXXX.XXXX.XXXX
max-calls-per-button 5
busy-trigger-per-button 3
username frank password 12345
presence call-list
type 7965
button  1:1

!

ephone  10
device-security-mode none
vm-device-id CUC-VI1
button  1:10
!        
ephone  11
device-security-mode none
vm-device-id CUC-VI2
button  1:11

3 Replies 3

john.nield
Level 1
Level 1

Hi

from you problem description it sounds like you VPIM integration is ok?

in you config i cannot see the incoming and outgoing SIP dial-peers between the CME and CUE,

i would suggest you run the debug CCSIP messages and check the MWI notify message is being sent to the CME, and what CME is sending back to CUE.

can you confirm the dial-peer config and send through the debug out.

thanks

John

Hey there. thank you for your reply.

The thing is that I integrated CME with Unity Connection ( not Unity Express) . And integration made over SCCP, so there is no need for SIP dial-peers according Cisco Doc.

Any advice ?

Have you tried the port status monitor to confirm that CUC is sending the MWI??

HTH

java

If this helps, please rate

www.cisco.com/go/pdihelpdesk

HTH

java

if this helps, please rate