08-27-2014 01:08 AM - edited 03-16-2019 11:54 PM
Hi All,
We are using CUCM System version: 8.5.1. we have a Board line number +91 44 4404 4000, the DIDs starts from +91 44 4404 4000 to +91 44 4404 4099.
at present when the user dial an outbound call their number displays as +91 44 4404 4000 (Board line number), but they want their actual DID to be displayed instead.
Please assist.
let me know for any clarification.
Thanks in Advance.
SIva.
08-27-2014 01:46 AM
can you post the voice gateway config
08-27-2014 02:01 AM
voice-card 0
!
!
!
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
h323
h225 h245-address on-connect
sip
registrar server expires max 3600 min 3600
!
voice class codec 99
codec preference 1 g711ulaw
!
voice class h323 1
h225 timeout tcp establish 3
!
hw-module pvdm 0/0
!
controller E1 0/0/0
framing NO-CRC4
pri-group timeslots 1-31 service mgcp
!
controller E1 0/0/1
framing NO-CRC4
pri-group timeslots 1-31 service mgcp
!
interface Serial0/0/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!
ccm-manager redundant-host 192.168.1.11
ccm-manager mgcp
no ccm-manager fax protocol cisco
ccm-manager music-on-hold
ccm-manager config server 192.168.1.10 192.168.1.11
ccm-manager config
ccm-manager sccp local GigabitEthernet0/0
!
mgcp
mgcp call-agent 192.168.1.10 2427 service-type mgcp version 0.1
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
mgcp package-capability pre-package
no mgcp package-capability res-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 inhibit
mgcp rtp payload-type g726r16 static
mgcp bind control source-interface GigabitEthernet0/0
mgcp bind media source-interface GigabitEthernet0/0
!
mgcp profile default
08-27-2014 02:26 AM
in case of MGCP the configuration is in the CUCM
check the transform mask in the dial patterns. also check the translation patterns
08-27-2014 06:28 AM
The easiest way would be to hardcode their own external phone number mask at DN level, and then make sure to check the option in the RP to use it for outbound calls.
08-27-2014 02:42 AM
Hi Siva,
In this case please let us know if the internal extensions have the same mask i.e 4000 to 4099 or different extensions.
Regards,
Mohamed Bedawy
08-27-2014 02:46 AM
Hi Mohamed,
Internal extensions have different mask
+91 44 4404 4000 to +91 44 4404 4099 >> 9200 to 9299
Regards,
Siva.
08-27-2014 04:31 AM
Hi Mohamed,
Any idea..
Thanks,
SIva.
08-27-2014 01:35 PM
hi Siva,
as the extensions are not in the same range, so the best way will be as our expert Jaime said. hard code each directory number with external phone number musk with his external number.
other ways will take a lot of work.
Regards.
08-29-2014 09:14 AM
Go to
Call Routing > Route/Hunt > Route List > (Choose the Route List used by your route pattern then click on it)
After, click on Route List Details (figure 1.png) and make sure that the field Use Calling Party's External Phone Number Mask is set to Active (figure 2.png)
Hope this helps!
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: