cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
5211
Views
3
Helpful
4
Replies

VG224 Error w/ stcapp

b0otable7
Level 1
Level 1

I am trying to set up a vg224 to work with CUCM.

I was following a config

1. enable

2. configure terminal

3. stcapp ccm-group group-id

4. stcapp

5. stcapp feature access-code

6. stcapp feature speed-dial

7. voice-port slot-number/port

8. timeouts initial seconds

...

Anway at step 4 I get:

STCAPP: Config error: SCCP stack not configured... exiting stcapp shutdown initiated... waiting for calls to clear.

Any Ideas what the problem might be, or how to fix it?    

4 Replies 4

frlindse
Cisco Employee
Cisco Employee

Hi Thomas,

Are the fXS ports registered to CUCM currently?  You will haver to shutdown sccp to make any changes.  What is the IOS version and the version of CUCM?

I needed to enable IP routing

alonsosolorzano
Level 1
Level 1

Hi Thomas

I got the same Error,

My Version Software (vg224-I6S-M), Version 12.4(24)T5

My config

!        
stcapp ccm-group 1
!
!

stcapp feature access-code
prefix #
call forward all 78
call forward cancel 79
pickup local 75
pickup group 74
!


!!
interface FastEthernet0/0
ip address 192.168.100.X 255.255.255.0
duplex auto
speed auto
!


voice-port 2/0
timeouts ringing infinity
!
voice-port 2/1
timeouts ringing infinity
!

!
mgcp fax t38 ecm
!
sccp local FastEthernet0/0
sccp ccm 192.168.100.x identifier 3 version 7.0
sccp ccm 192.168.100.x identifier 1 version 7.0
sccp
!
sccp ccm group 1
associate ccm 1 priority 1
associate ccm 3 priority 3
!
!

dial-peer voice 1 pots
service stcapp
port 2/0
!
dial-peer voice 2 pots
service stcapp
port 2/1
!


VG-MCVG224-01# sh sccp all
SCCP Admin State: UP
Gateway Local Interface: FastEthernet0/0
        IPv4 Address: 192.168.100.x
        Port Number: 2000
IP Precedence: 5
User Masked Codec list: None
Call Manager: 192.168.100.11, Port Number: 2000
                Priority: N/A, Version: 7.0, Identifier: 3
                Trustpoint: N/A
Call Manager: 192.168.100.x, Port Number: 2000
                Priority: N/A, Version: 7.0, Identifier: 1
                Trustpoint: N/A

SCCP application services(dspfarm profiles) are not enabled
or haven't associated to SCCP CCM group

CCM Group Identifier: 1
Description: None
Binded Interface: None
Associated CCM Id: 1, Priority in this CCM Group: 1
Associated CCM Id: 3, Priority in this CCM Group: 3
Registration Retries: 3, Registration Timeout: 10 sec
Keepalive Retries: 3, Keepalive Timeout: 30 sec
CCM Connect Retries: 3, CCM Connect Interval: 10 sec
Switchover Method: GRACEFUL, Switchback Method: GRACEFUL_GUARD
Switchback Interval: 10 sec, Switchback Timeout: 7200 sec
Signaling DSCP value: cs3, Audio DSCP value: ef

Total number of active session(s) 0, and connection(s) 0


Total number of active session(s) 0, and connection(s) 0


Total number of active session(s) 0, connection(s) 0, and callegs 0

SCCP Application Service(s) Statistics Summary:
Total Conferencing Sessions: 0, Connections: 0
Total Transcoding Sessions: 0, Connections: 0
Total MTP Sessions: 0, Connections: 0
Total ALG-Phone Sessions: 0, Connections: 0
Total BRI-Phone Sessions: 0, Connections: 0
Total SCCP Sessions: 0, Connections: 0


Total active sessions 0, connections 0, rsvp sessions 0
No SCCP server info to display
VG-MCVG224-01#VG-MCVG224-01#

VG-MCVG224-01#sh stcapp feature codes

  stcapp feature access-code
    malicious call ID (MCID) ***
    prefix #
    call forward all #78
    call forward cancel #79
    pickup local group #75
    pickup different group #74
    pickup direct #6
    meetme-conference #5

  stcapp feature speed-dial disabled

stcapp call-control mode is standard mode

VG-MCVG224-01#

*******************************************************************************************************

I can't activate the STCAPP !!!

STCAPP: Config error: SCCP stack not configured... exiting stcapp shutdown initiated... waiting for calls to clear.

Hola  que tal     tengo el mismo error en el  VG   lo que  hice   y ya me funciono  fue lo siguiente :

 

 

1.- negue los servicios  de sccp  y los di de baja

2.- los volvi a crear  para que se firmara  con el CUCM

3.-  volvia generar los servicios de stcapp ccm-group 1

 stcapp

 

4.- DONE !!!!

 

 

funciono mi  vg se firma  y despues de  haberlo hecho   ya funciono correctamente

 

INTENTENLO

 :)

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: