cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1195
Views
5
Helpful
3
Replies

VG224 in MGCP can be helped by GW in SRST ?

MBO46
Level 1
Level 1

Hello everybody,

To have the VG224 operational in SRST, i configure it in SCCP on the CUCM.

If i use MGCP to configure VG224, can i have the voice gateway registered on the GW in SRST ?

Thanks,

Matthieu

3 Replies 3

Karthik Sivaram
Level 4
Level 4

Hello Matthieu,

I can think of 3 ways having srst with vg224 (3 options):

1.Changing the protocol of the VG224 to SCCP (easiest way to do it) as the following

example:

sccp local Loopback104

sccp ccm 10.104.20.101 identifier 101 version 4.1

sccp ccm 10.104.96.108 identifier 108 version 4.1

sccp ccm 10.104.96.104 identifier 104 version 4.1

sccp ccm 10.104.120.200 identifier 200 version 4.1

sccp

!

sccp ccm group 105

associate ccm 104 priority 1

associate ccm 108 priority 2

associate ccm 101 priority 3

associate ccm 200 priority 4

Where 10.104.120.200 is the SRST gateway. Add the srst reference in the device pool of the vg224

2.Applying the command the following commands to the MGCP gateway

ccm-manager fallback-mgcp

application

global

service alternate default

And configure dial-peers for H323 in case the router goes to SRST mode.

3.Convert the protocol to H323 and create 2 dial-peer one of them with preference 1 with

destination pattern , dial-peer two with preference 2 with

destination pattern

Hope this helps!

Thanks,

Karthik

Thanks Karthik,

I used only the first possibility, i will test the two others.

Thanks

Hi Karthik,

I just followed SCCP configuration, however i can not dial out between VG224 and SRST IP phone.

do i need to have dial-peer no SCCP ?

I could see VG224 successfully registerted to SRST VGW by command show ephone registration.

HQ-Tokyo#sh ephone summary

ephone-1 Mac:0017.9551.F7EA TCP socket:[2] activeLine:0 REGISTERED
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 debug:0
IP:142.100.64.102 7941   keepalive 38  1:2  CM Fallback

ephone-2 Mac:0017.954A.47B0 TCP socket:[1] activeLine:0 REGISTERED
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 debug:0
IP:142.100.64.104 7971   keepalive 39  1:1 2:2  CM Fallback

ephone-3 Mac:5C26.0A27.4C00 TCP socket:[3] activeLine:0 REGISTERED
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 debug:0
IP:192.168.128.150 CIPC   keepalive 35   CM Fallback
sp1:3001

ephone-4 Mac:FB9E.EB2E.C400 TCP socket:[4] activeLine:0 REGISTERED ----> VG224
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 debug:0
IP:10.10.10.1 SCCP Gateway (AN)  keepalive 21   CM Fallback


ephone-5 Mac:FB9E.EB2E.CFFF TCP socket:[5] activeLine:0 REGISTERED  ----> VG224
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 debug:0
IP:10.10.10.1 Unknown 30032  keepalive 21

however i can not see any destination pattern by command sh dial-peer voice summary.

HQ-Tokyo#sh dial-peer voice summary

dial-peer hunt 0

             AD                                    PRE PASS                OUT

TAG    TYPE  MIN  OPER PREFIX    DEST-PATTERN      FER THRU SESS-TARGET    STAT PORT

999300 pots    up   up                     0         down 3/0/0  ----> VG224 digits                                                    

20001  pots     up   up             2002$              0                           50/0/1

20002  pots     up   up             2001$              0                           50/0/2

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: