04-11-2013 08:21 AM - edited 03-16-2019 04:45 PM
Hi
We have a CUCME connected to the ITSP via a SIP trunk. Some incoming calls fail with cause code 172. In the debugs I could see this just before the SIP BYE message:
%VOICE_IEC-3-GW: VTSP: Internal Error (DSP unknown failure): IEC=1.1.182.9.22.10
#show voice iec description 1.1.182.9.22.10
IEC Version: 1
Entity: 1 (Gateway)
Category: 182 (Hardware Resources Unavailable)
Subsystem: 9 (VTSP)
Error: 22 (DSP unknown failure)
Diagnostic Code: 10
The call-leg on the SIP trunk is always alaw, internally between CUCME and CUE or the phones is always ulaw. We have a transcoder active.
What debugs can I run to check if this is a DSP allocation error, or if there is a hardware issue, or... ?
Thanks!
04-11-2013 08:38 AM
You can use
show voice dsp group all..
This will show if you hava had dsp allocation failure
Please rate all useful posts
"opportunity is a haughty goddess who waste no time with those who are unprepared"
04-12-2013 06:17 AM
Thanks aokanlawon, I don't have access to the customer network right now but i'll try this and let you know the output soon.
04-16-2013 07:27 AM
Hi aokanlawon
It doesn't look like a DSP allocation issue:
show voice dsp group all
DSP groups on slot 0:
dsp 1:
State: UP, firmware: 26.3.7
Max signal/voice channel: 43/43
Max credits: 645
num_of_sig_chnls_allocated: 42
Transcoding channels allocated: 0
Group: FLEX_GROUP_VOICE, complexity: FLEX
Shared credits: 630, reserved credits: 0
Signaling channels allocated: 42
Voice channels allocated: 1
Credits used (rounded-up): 15
Voice channels:
Ch01: voice port: 0/2/0, codec: g711alaw, credits allocated: 15
Slot: 0
Device idx: 0
PVDM Slot: 0
Dsp Type: SP2600
dsp 2:
State: UP, firmware: 26.3.7
Max signal/voice channel: 43/43
Max credits: 645
num_of_sig_chnls_allocated: 17
Transcoding channels allocated: 12
Group: FLEX_GROUP_VOICE, complexity: FLEX
Shared credits: 403, reserved credits: 0
Signaling channels allocated: 0
Voice channels allocated: 0
Credits used (rounded-up): 0
Group: FLEX_GROUP_XCODE, complexity: MEDIUM
Shared credits: 0, reserved credits: 242
Transcoding channels allocated: 1
Credits used (rounded-up): 21
Slot: 0
Device idx: 0
PVDM Slot: 0
Dsp Type: SP2600
dsp 3:
State: UP, firmware: 26.3.7
Max signal/voice channel: 42/43
Max credits: 645
num_of_sig_chnls_allocated: 0
Transcoding channels allocated: 0
Group: FLEX_GROUP_VOICE, complexity: FLEX
Shared credits: 645, reserved credits: 0
Signaling channels allocated: 0
Voice channels allocated: 0
Credits used (rounded-up): 0
Slot: 0
Device idx: 0
PVDM Slot: 0
Dsp Type: SP2600
DSP groups on slot 1:
This command is not applicable to slot 1
DSP groups on slot 2:
This command is not applicable to slot 2
DSP groups on slot 3:
This command is not applicable to slot 3
DSP groups on slot 4:
This command is not applicable to slot 4
0 DSP resource allocation failure
Any idea?
Thanks!
04-29-2013 03:36 AM
FYI: the issue did not reoccur so far...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: