08-03-2021 11:42 AM
Hi
I Have 3 phones registered in SRST mode ( wan is down )
What will occur if the phones got power cycle ?
Did the phones should get registered again ?
from what I see the phones not registered and didnot get IP address from the DHCP .
Thanks
Eli
08-03-2021 07:22 PM
Configure a local DHCP with option 150 as your HQ.
08-03-2021 11:33 PM
Can these phones reach the DHCP server?
08-04-2021 12:47 AM
I configured DHCP in SRST , and lines goes registered and that its ok ...
and 3 Dial-peer was rebuilt in SRST .
The issue is while one of the phones was reset and registered again , the srst built a new Dial-peer with the same Number .
so we got a duplicate dial-peer with the same number registered
please see Registered status :
Router# show sip-ua status registrar
Line destination expires(sec) contact
transport call-id
peer
============ =============== ============ ===============
3029991 10.2.30.108 388 10.2.30.108
TLS 00120014-4ae40064-f1a3e9fe-8d301072@10.2.30.1
40004
3029993 10.2.30.103 382 10.2.30.103
TLS 001bd433-1c840052-655cd596-4e992eed@10.2.30.1
40011
3029982 10.2.30.106 406 10.2.30.106
TLS 001d452c-dbba0056-0481d321-1f3f848d@10.2.30.1
40001
3029982 10.2.30.106 0 10.2.30.106
TLS 001d452c-dbba0056-0481d321-1f3f848d@10.2.30.1
40001
As you see the last line show expired="0"
In this time while the WAN is back the all Registered record should be cleared from the SRST
BUT the last line still exist
3029982 10.2.30.106 0 10.2.30.106
TLS 001d452c-dbba0056-0481d321-1f3f848d@10.2.30.1
40001
How can I cleared this record Line ?
Thanks
Eli
08-04-2021 03:01 AM
Hi
DHCP was configured in SRST
Phones got Registration and that its ok .
I have a scenario while IN SRST mode one of the phone lost connection and tried to registered again
The Phone was registered ok but while running --> show sip-ua status registrar
I have got duplicate number and Dial-peer :
Router# show sip-ua status registrar
Line destination expires(sec) contact
transport call-id
peer
============ =============== ============ ===============
3029991 10.2.30.108 388 10.2.30.108
TLS 00120014-4ae40064-f1a3e9fe-8d301072@10.2.30.1
40004
3029993 10.2.30.103 382 10.2.30.103
TLS 001bd433-1c840052-655cd596-4e992eed@10.2.30.1
40011
3029982 10.2.30.106 406 10.2.30.106
TLS 001d452c-dbba0056-0481d321-1f3f848d@10.2.30.1
40001
3029982 10.2.30.106 0 10.2.30.106 <======== Expired ==0
TLS 001d452c-dbba0056-0481d321-1f3f848d@10.2.30.1
40001
As you see we got Duplicate Dial-peer and of them with Expired=0
then the WAN is back .. In that time all Dial-peer should removed from this table
But the one with Expired=0 still exist
How to avoid this situation ? How can we remove this line
Thanks
Eli
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide