We're in the process of replacing a long list of Nexus C3064PQ chassis with C93180YC-FX3s. Many of those 3064s are paired together and have a crosslink configured for IPv4 and IPv6 for iBGP peering. For some reason, we cannot get IPv6 working (not ev...
Forum Posts
Resolved! NAT64 DROPS COMING FROM IPV6 TO IPV4
***Configuration on Bridge Domain for NAT64 on IR8340 ************* interface BDI1ip address 9.1.1.2 255.255.255.0ipv6 address 3001:11:0:1::1/64ipv6 enableencapsulation dot1Q 11nat64 enableend nat64 prefix stateful 3001::/96nat64 v4v6 static 9.1.1.3...
Hello,I am pretty new to this. So i was configuring this network(attachment below) and made an DHCP so that my SBC and PC1 could receive ipv6 addresses automatically. My PC1 gets an ipv6 address from range but my SBC won't whatever I do. So I came he...
Resolved! ipv6
Configuration :!ipv6 unicast-routingipv6 dhcp pool IT_User_IPV6address prefix 2001:BF2:640:1AB::/64 lifetime infinite infinitelink-address 2001:BF2:640:1AB/64dns-server 2001:4860:4860::8888domain-name seddeeq.com!interface GigabitEthernet0/2.276desc...
I am doing a cisco learning for KPSI1-ZS2023 (networks)and i spotted some error which is confusing in cisco learning exam-quiz 9.4.2 .this one ->https://contenthub.netacad.com/itn-dl/9.4.2according to cisco learning materials from topic 9.3.0 , corre...
Greetings allPlease help me I'm struggling with identifying LANs,WANs,and ISP on this network diagram
Hello everyone, I'm having some trouble understanding how OSPFv6 calculates costs in IPv6.Attached are screenshots of some show commands on both routers.My question is: why OSPF is not adding the cost of the interface loopback to the metric.Thank you...
Resolved! Counter for SVI on 4500X
Hi everyoneI have recently setup IPv6 routing on my Cisco 4500x and ran into problem for calculating the rate of traffic.i have 2 Vlan Interfaces which are for ipv4 and ipv6 routing. the "counter" command is applied to both interfaces.the Vlan interf...
How should I go about configuring IPv6 in this case:I have this topology, in the yellow network I have VLAN 10 and VLAN 20 configured for IPv4, and in the upper-right network there is VLAN 30, VLAN 40 and VLAN 99. I would like to configure IPv6 on ea...
I have this topology and I don't know why the pings don't work properly across networks, and even in the same network for vlan 10 and 20. Circled with black are the vlans.Every device is properly configured with an ipv6 address and a gateway (SW and ...
Resolved! STATEFUL NAT64
My LAN side running IPV6 and WAN side IPV4. I want to access internet from my IPV6-only host. I have attached my topology. If need i can change the topology. ip route 0.0.0.0 0.0.0.0 192.168.1.1 // To R2 For internet!interface Ethernet0/1ip address 1...
In terms of "work the host has to do", I would say that there is no difference between all the methods EXCEPT for manual, they are all automatic and decided by the upstream devices.Manual requires someone to actually configure the IPs, but all other ...
Resolved! Native IPv6 & 464xlat
Do any current cisco equipment support 464xlat? My goal is to either transition to ipv6 or even better start with ipv6. My understanding is if there's applications that need ipv4, 464xlat can take care of them in some instances.
We are rolling out IPv6 in our network. When a client is assigned both an IPv6 address and an IPv4 address, it doesn't get any IPv4 traffic. If it is only assigned an IPv4 address, the IPv4 traffic works as it should. IPv6 traffic works normally in a...
MechanismScenarioTargeted EnvironmentDesign ConcernDual StackEnd-to-End IPv6 + IPv4Any Environment that ultimately needs to move to end-to-end IPv6IPv6 support in all L3 ware platforms is required.Increased control plane complexity.May introduce scal...
