cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

3156
Views
0
Helpful
8
Replies
Beginner

IPv6 & IP SLA config

Hi Team,

I'm looking for IPv6 IP SLA config for my c3845. The plan is to ping the remote site and if it timeout, then this will generate syslog or SNMP trap.

I checked " Configuring ICMP Echo Operations" Cisco document and all config for IPv4 not Ipv6. I tried diffrent IOS ie.. c3845-adventerprisek9-mz.151-4.M.bin and still not seeing IPv6 x:x:x:: under icmp-echo.

Any idea?

Thanks

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: IPv6 & IP SLA config

FN says it’s supported with 15.1(4)M and I verified it as well on a router running 15.1(4)M1:

R1(config)#ip sla 1

R1(config-ip-sla)#icmp-echo ?

  Hostname or X:X:X:X::X

  Hostname or A.B.C.D  Destination IPv6/IP address or hostname

You should open a SR with the TAC as something is definitely going wrong in your setup

Thanks,

Laurent

8 REPLIES 8
Beginner

IPv6 & IP SLA config

hm, maybe you need

ping ipv6 xxx:xx:xx:xx:x  ?

Beginner

IPv6 & IP SLA config

Need someting automatic to check/ping every 5 second, and if unable to ping the remote site then this will generate trap to the server either (SNMP or Syslog).

I found some config in the link below. However looking to see if someone know what IOS it support in the C3800. Itried

c3845-adventerprisek9-mz.124-24.T2.bin & c3845-adventerprisek9-mz.151-4.M. and no luck.

Thanks

ip sla 1
 icmp-echo 2001::214:A8FF:FE7A:ED70
ip sla schedule 1 start-time now


source:

http://docwiki.cisco.com/wiki/IOS_IP_SLAs_for_IPv6_White_Paper#Configuration_Examples
Highlighted
Cisco Employee

Re: IPv6 & IP SLA config

Hi,

It’s not enabled by default. Please use the ip sla logging trap command. Please refer to the link below for usage guidelines:

http://www.cisco.com/en/US/docs/ios/ipsla/command/reference/sla_02.html#wp1052104

HTH

Laurent.

Beginner

Re: IPv6 & IP SLA config

Thank Laurent, do you know which code/feature set to use with c3800?

as I tried 3 codes and when i enable IP SLA see below I did not see v6 choice, I'm looking for a code that will show up IPv6 address like v4 address below:

AN1212#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

AN1212(config)#ip sla 1

AN1212(config-ip-sla)#icmp-echo ?

  Hostname or A.B.C.D  Destination IP address or hostname, broadcast disallowed

Thanks for the help.

Maz

Cisco Employee

Re: IPv6 & IP SLA config

FN says it’s supported with 15.1(4)M and I verified it as well on a router running 15.1(4)M1:

R1(config)#ip sla 1

R1(config-ip-sla)#icmp-echo ?

  Hostname or X:X:X:X::X

  Hostname or A.B.C.D  Destination IPv6/IP address or hostname

You should open a SR with the TAC as something is definitely going wrong in your setup

Thanks,

Laurent

Beginner

Re: IPv6 & IP SLA config

Thanks Laurent,

15.1(4)M1 with adventerprisek9- feture set supported IPv6 IP SLA. Need of course to enable IPv6 and assign IPv6 address on the interface to see the

R1(config-ip-sla)#icmp-echo ?

  Hostname or X:X:X:X::X

Thanks again,

Maz

Beginner

Re: IPv6 & IP SLA config

Hello everyone, i'm using c7200-adventerprisek9-mz.152-4.M7.image and it does not support ipv6 SLA. Which ios of C7200 support the SLA for ipv6?

Beginner

Re: IPv6 & IP SLA config

I found some config in the link below. However looking to see if someone know what IOS it support in the C3800. Itried    https://xender.pro/ https://discord.software/ https://omegle.onl/

CreatePlease to create content
Content for Community-Ad
July's Community Spotlight Awards


This widget could not be displayed.