cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
5447
Views
0
Helpful
5
Replies

Native IPv6 & 464xlat

Do any current cisco equipment support 464xlat? 

 

My goal is to either transition to ipv6 or even better start with ipv6. My understanding is if there's applications that need ipv4, 464xlat can take care of them in some instances.

1 Accepted Solution

Accepted Solutions

I would recommend you look at MAP-T. MAP-T allows you to offer dual stack to your customer, but over an IPv6 only network. So like xlat it also use a NAT464 paradigm. MAP-T does stateless translation and therefore would scale much better than 464XLAT that uses stateful translation on the PLAT.

 

For more information on MAP-T, please refer to the following documents:

 

https://blogs.cisco.com/sp/a-map-to-easier-more-scalable-ipv6-deployments

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipaddr_nat/configuration/xe-3s/nat-xe-3s-book/ip-nat-divi-v4v6.pdf

 

Regards,

 

 

Harold Ritter
Sr Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México
Paseo de la Reforma 222
Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México

View solution in original post

5 Replies 5

Harold Ritter
Cisco Employee
Cisco Employee

Can you tell us more about the type of deployment for which you are considering XLAT464? Unless it is for a mobile (4G, LTE) network, this is probably not for you.

 

Regards,

Harold Ritter
Sr Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México
Paseo de la Reforma 222
Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México

the setup is a WISP (wireless ISP). Different routes to the internet may be fiber, coaxial, or even 4G although currently we are using majority fiber. The customers will use proprietary mimosa, ubiquiti style dishes at their location.

 

The issue arose that each customer may want their own public ipv4 address, and ARIN isn't handing out anymore. so the idea to use ipv6 fully raises the question of compatibility and having customers access everything that's already on ipv4 addresses.

I would recommend you look at MAP-T. MAP-T allows you to offer dual stack to your customer, but over an IPv6 only network. So like xlat it also use a NAT464 paradigm. MAP-T does stateless translation and therefore would scale much better than 464XLAT that uses stateful translation on the PLAT.

 

For more information on MAP-T, please refer to the following documents:

 

https://blogs.cisco.com/sp/a-map-to-easier-more-scalable-ipv6-deployments

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipaddr_nat/configuration/xe-3s/nat-xe-3s-book/ip-nat-divi-v4v6.pdf

 

Regards,

 

 

Harold Ritter
Sr Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México
Paseo de la Reforma 222
Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México

The deployment type of XLAT464 is being considered.   The object is an LTE 4G network

 

Can I get support for this request and provide environment deployment tutorials

Review Cisco Networking for a $25 gift card