The thing is both bundles are configured exactly the same, down to the number of interfaces.
RP/0/RSP0/CPU0:xxxxxxxxx#show int bundle-ether 1 Tue Aug 5 10:39:13.124 CST Bundle-Ether1 is up, line protocol is up Interface state transitions: 3 Hardware is Aggregated Ethernet interface(s), address is 0026.982c.0d5b Description: Internet address is x.x.x.x/30 MTU 9216 bytes, BW 80000000 Kbit (Max: 80000000 Kbit) reliability 255/255, txload 1/255, rxload 23/255 Encapsulation ARPA, Full-duplex, 80000Mb/s loopback not set, ARP type ARPA, ARP timeout 04:00:00 No. of members in this bundle: 8 TenGigE0/4/0/0 Full-duplex 10000Mb/s Active TenGigE0/4/0/1 Full-duplex 10000Mb/s Active TenGigE0/4/0/2 Full-duplex 10000Mb/s Active TenGigE0/4/0/3 Full-duplex 10000Mb/s Active TenGigE0/4/0/4 Full-duplex 10000Mb/s Active TenGigE0/4/0/5 Full-duplex 10000Mb/s Active TenGigE0/4/0/6 Full-duplex 10000Mb/s Active TenGigE0/4/0/7 Full-duplex 10000Mb/s Active
RP/0/RSP0/CPU0:xxxxxxxxxx#show int bundle-ether 2 Tue Aug 5 10:40:14.732 CST Bundle-Ether2 is up, line protocol is up Interface state transitions: 1 Hardware is Aggregated Ethernet interface(s), address is 0026.982c.0d5a Description: Internet address is x.x.x.x/30 MTU 9216 bytes, BW 80000000 Kbit (Max: 80000000 Kbit) reliability 255/255, txload 6/255, rxload 10/255 Encapsulation ARPA, Full-duplex, 80000Mb/s loopback not set, ARP type ARPA, ARP timeout 04:00:00 No. of members in this bundle: 8 TenGigE0/7/0/0 Full-duplex 10000Mb/s Active TenGigE0/7/0/1 Full-duplex 10000Mb/s Active TenGigE0/7/0/2 Full-duplex 10000Mb/s Active TenGigE0/7/0/3 Full-duplex 10000Mb/s Active TenGigE0/7/0/4 Full-duplex 10000Mb/s Active TenGigE0/7/0/5 Full-duplex 10000Mb/s Active TenGigE0/7/0/6 Full-duplex 10000Mb/s Active TenGigE0/7/0/7 Full-duplex 10000Mb/s Active
Hi, I want to redistribute OMP routes to BGP, i have the doubt if all of the OMP prefixes located in the local vEdge will be redistributed to BGP or just the connected+static networks located in the vEdge. Also how can i restrict some OMP prefix...
Let's say we have two routers configured as RP candidates for auto-RP: R1 - "advertising" its loopback0 interface IP address 18.104.22.168 as the RP for these groups:22.214.171.124/32126.96.36.199/32188.8.131.52/24184.108.40.206/16 R2 - "advertising" its loopback0 int...
hi,i just performed an IOS upgrade and got a report that admin can't create L2 VLANs.i noticed the 'vtp primary force' and 'vtp primary mst' was applied to one of the core switch and perhaps got lost after the upgrade.how to keep the VTP primary persisten...
Meet the Authors Event - How to Troubleshoot Network Problems with Vinit Jain
(Live event – Wednesday, February 12th, 2020 at 10:00 a.m. Pacific / 1:00 p.m. Eastern / 7:00 p.m. Paris)
This event had place on Wednesday 12th, February 2020 at 10hrs PDT ...