cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
127
Views
1
Helpful
6
Replies
Highlighted
Cisco Employee

Tail-f HCC Package

I am trying to setup the HA cluster for NCS , I am trying to install the tail-hcc package.

/var/opt/ncs/packages

[root@nso-172-62 packages]# ls

ncs-3.3-tailf-hcc-3.0.9.tar.gz  ncs-3.4-quagga-bgp-3.1.0.1_21ae8a0.tar.gz

admin@ncs> request packages reload

>>> System upgrade is starting.

>>> Sessions in configure mode must exit to operational mode.

>>> No configuration changes can be performed until upgrade has completed.

>>> System upgrade has been cancelled.

Error: /var/opt/ncs/state/packages-in-use/1/tailf-hcc/load-dir/tailf-ned-tailf-hcc-id.fxs: Must be recompiled!

[error][2015-05-27 18:55:00]

Currently the NCS version running is 3.4.1

I get the above error. Could you let me know the upgrade version of ncs needed.

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: Tail-HCC Package

I think Sujay has simplified the logs, he sent. I gave him the packages and asked to copy packages in folder “/opt/ncs/packages” and create sym-links for these packages in “/var/opt/ncs/packages”.

Sujay, at the moment your problem looks to be that the packages being imcompatible with NCS version you have. I don’t there is any change in quagga packages. So if you just recompile the packages (under your NCS version), you should be fine.

6 REPLIES 6
Cisco Employee

Re: Tail-HCC Package

If you are running NCS 3.4.1, you may want to consider running the most recent version of HCC package (ncs-3.4.1-tailf-hcc-3.0.9.1.tar.gz). Copying Larry to see if this latest version is ready to be shared.

Cisco Employee

Re: Tail-HCC Package

Please remove the tar.gz files from the packages folder. There should be nothing else that the packages you want to load there.

Cisco Employee

Re: Tail-HCC Package

I think Sujay has simplified the logs, he sent. I gave him the packages and asked to copy packages in folder “/opt/ncs/packages” and create sym-links for these packages in “/var/opt/ncs/packages”.

Sujay, at the moment your problem looks to be that the packages being imcompatible with NCS version you have. I don’t there is any change in quagga packages. So if you just recompile the packages (under your NCS version), you should be fine.

Cisco Employee

Re: Tail-HCC Package

Yes use the new package that Nik has mentioned, I think Imran is successfully using it.

The problem experienced below is that you are trying to run  ncs-3.3-tailf-hcc-3.0.9.tar.gz built for 3.3 with NCS 3.4.

Cisco Employee

Re: Tail-HCC Package

Configuring the ha cluster config , I am able to see the master node but not the slave node.

[root@nso-172-62 ~]# hostname

nso-172-62

[root@nso-172-62 ~]# ncs_cli -u admin

admin connected from 10.156.49.88 using ssh on nso-172-62

admin@ncs> show ha-cluster

NAME        STATUS  

---------------------

nso-172-62  master  

nso-172-63  unknown

admin@ncs% show ha-cluster

auto-start disable;

master-ip {

    enable;

    vip    10.10.10.1;

    member nso-172-62 {

        interface ens224;

    }

    member nso-172-63 {

        interface ens224;

    }

}

members nso-172-62 {

    address 10.10.30.3;

    role    master;

}

members nso-172-63 {

    address            10.10.20.3;

    role               slave;

    transition-enabled true;

    master-capable     true;

}

[ok][2015-05-28 16:56:37]

[edit]

admin@ncs%

Could you please let me know if anything is missed.

Cisco Employee

Re: Tail-HCC Package

Could you please share the path wiki or repository for the Tailf-f HCC and other packages needed for NCS – HA setup.

Content for Community-Ad
August's Community Spotlight Awards