Metro

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

I am finding references to SPA's with support up to 8000 vlans with restriction of 4000 for dot1q. I can't find any reference on how to use the range up to 8000. Everything says support for it, but how? Is it a new encapsulation?Thanks,Greg

Which is the lowest series router i need to test VPLS or Pseudowire in LAB? Will 26XX or 37XX will support the VPLS and Pseudowire testing?

dangal.43 by Level 1
  • 1168 Views
  • 4 replies
  • 0 Helpful votes

i have STM-1 card STM-1 Port Adapter (PA-MC-STM-1) on router cisco 7206 & i need to divide it according to the following:1-one PVC that carry 40Mbps net(without framing).2-another PVC that carry 40Mbps net(without framing).3-the third PVC will carry ...

Hello.We want to use a ME-3400G-2CS with IOS METRO IP as router CE for access to an MPLS VPN.The ME-3400 will be the default gateway about 1500 IP Client.Are there problems for this configuration (arp-table dimensions and so on)?Thanks.

pbenin by Level 1
  • 615 Views
  • 1 replies
  • 0 Helpful votes

Dear All,I am trying to increase bandwidth between my 7600s running as PE/Prouters with 1G line cards terminating dark fibre links. I am exploring the following two options:Option I---------- replace the 1G lines cards with 10G on the 7600s - termin...

WAE installed between two sites for NAS filer replication has failed during numerious attempts to kick off NetApp SnapMirror Replication. When we turn off TCP optimization, compression and application services the replication continues. Cisco CCIE lo...

mlenco by Level 1
  • 827 Views
  • 2 replies
  • 0 Helpful votes

We are planning to use 7600-SIP-400 with SPA-2X1GE-V2.Can you assure that the two rj45 ports at the SPA-2X1GE-V2 supporting 10 or 100baseT connections? (speed 100) ThanksChristian

cgrodde by Level 1
  • 930 Views
  • 1 replies
  • 0 Helpful votes

Our service provider for Metro E point to multipoint said to set the p bit to 5 for H323 on the router. What is the p bit and how is it set on the router?

hello, what are the benifits of differnt EoMPLS technologies like Port mode, Vlan mode and dot1q mode? can any one explain me which one is appropriate for what kind of scenarios? regards Devang

Does new Ethernet service card ES20-GE3C support only SFP-GE (DOM) tranceivers, or tranceives GLC-LH-SM and GLC-SX-MM is also supported and working in this card?

gdzenan by Level 1
  • 699 Views
  • 1 replies
  • 0 Helpful votes

Hi, What could cause input queue drop in a FastEthernet interface connected to MetroE beside those mentioned in this link http://www.cisco.com/en/US/products/hw/routers/ps133/products_tech_note09186a0080094791.shtml I'm experiencing slow/degrading da...

Danilo Dy by VIP Alumni
  • 946 Views
  • 2 replies
  • 0 Helpful votes

Hi,we need to temporary setup the ME3400 switch to interconnect the two sites. Could somebody tell me how to configure the ME3400 based on the attached network diagram. I only have one unit of the ME3400 switch loan from cisco.

Chaikf by Level 1
  • 834 Views
  • 1 replies
  • 0 Helpful votes

Hi!I configured 1 VRF in a 7600. I need to send some packets from the global table to that VRF. I configured 2 ports, one in the global table and the other in the VRF and join the 2 ports with a crossover cable. To send the traffic to the VRF i used ...

ccomelli by Level 1
  • 754 Views
  • 2 replies
  • 0 Helpful votes

I am creating cwdm diagram describes below;Cat6500(HQ) --> CWDM-MUX8 --> OADM-4-1 --> Cat3560E-Site1 (CWDM-SFP) --> Cat3560E-SiteN (CWDM-SFP) --> CWDM-MUX8 (HQ)I want to connect using only one single fiber link in ring topology (physical ring & logic...