cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1197
Views
0
Helpful
3
Replies
Highlighted

MPLS ATOM Between 2 ME-3600X-24FS-M

hello all

i need to get up an L2VPN between 2 switch ME-3600X-24FS-M

i think the config is fine all show are OK

but i cant L2 link doesnt work, no ping between 2 CE

here the show

MES.M20.thn.icosnet.net#sho mpls L2transport vc 102 detail

Local interface: Gi0/12 up, line protocol up, Eth VLAN 102 up

  Interworking type is Ethernet

  Destination address: 10.255.255.11, VC ID: 102, VC status: up

    Output interface: Gi0/11, imposed label stack {88 27}

    Preferred path: not configured 

    Default path: active

    Next hop: 172.16.33.1

  Create time: 21:19:46, last status change time: 21:19:46

    Last label FSM state change time: 21:19:46

  Signaling protocol: LDP, peer 10.255.255.11:0 up

    Targeted Hello: 10.255.255.10(LDP Id) -> 10.255.255.11, LDP is UP

    Status TLV support (local/remote)   : enabled/supported

      LDP route watch                   : enabled

      Label/status state machine        : established, LruRru

      Last local dataplane   status rcvd: No fault

      Last BFD dataplane     status rcvd: Not sent

      Last BFD peer monitor  status rcvd: No fault

      Last local AC  circuit status rcvd: No fault

      Last local AC  circuit status sent: No fault

      Last local PW i/f circ status rcvd: No fault

      Last local LDP TLV     status sent: No fault

      Last remote LDP TLV    status rcvd: No fault

      Last remote LDP ADJ    status rcvd: No fault

    MPLS VC labels: local 28, remote 27

    Group ID: local 0, remote 0

    MTU: local 1500, remote 1500

    Remote interface description:

  Sequencing: receive disabled, send disabled

  Control Word: On (configured: autosense)

  Dataplane:

    SSM segment/switch IDs: 4117/4116 (used), PWID: 1

  VC statistics:

    transit packet totals: receive 35, send 8815

    transit byte totals:   receive 3090, send 602000

    transit packet drops:  receive 0, seq error 0, send 0

MES.M20.thn.icosnet.net# sho xconnect all

Legend:    XC ST=Xconnect State  S1=Segment1 State  S2=Segment2 State

  UP=Up       DN=Down            AD=Admin Down      IA=Inactive

  SB=Standby  HS=Hot Standby     RV=Recovering      NH=No Hardware

XC ST  Segment 1                         S1 Segment 2                         S2

------+---------------------------------+--+---------------------------------+--

UP pri   ac Gi0/12:102(Eth VLAN)         UP mpls 10.255.255.11:102            UP

MES.M20.thn.icosnet.net#sho mpls ldp neighbor

    Peer LDP Ident: 10.255.255.1:0; Local LDP Ident 10.255.255.10:0

        TCP connection: 10.255.255.1.646 - 10.255.255.10.57123

        State: Oper; Msgs sent/rcvd: 1476/1480; Downstream

        Up time: 21:24:44

        LDP discovery sources:

          GigabitEthernet0/11, Src IP addr: 172.16.33.1

        Addresses bound to peer LDP Ident:

          193.251.154.130 196.41.228.193  10.255.255.1    195.59.77.2    

          172.16.44.1     172.16.44.249   172.16.44.13    172.16.33.1    

          1.1.1.1        

    Peer LDP Ident: 10.255.255.11:0; Local LDP Ident 10.255.255.10:0

        TCP connection: 10.255.255.11.61641 - 10.255.255.10.646

        State: Oper; Msgs sent/rcvd: 1484/1480; Downstream

        Up time: 21:20:23

        LDP discovery sources:

          Targeted Hello 10.255.255.10 -> 10.255.255.11, active, passive

        Addresses bound to peer LDP Ident:

          172.31.3.202    10.255.255.11   172.16.33.6

regards.

3 REPLIES 3
Highlighted

MPLS ATOM Between 2 ME-3600X-24FS-M

Hello Hamou,

Would you be so kind to capture from both sides of PW:

# show version

# show mpls l2 vc 102 detail

Thank you

-- 
Best regards,
Dmitry Skotnikov

-- Best regards, Dmitry Skotnikov
Highlighted
Participant

MPLS ATOM Between 2 ME-3600X-24FS-M

Hello Hamou,

Have you tried changing the interworking type please?

adam

adam
Highlighted
Beginner

MPLS ATOM Between 2 ME-3600X-24FS-M

Are you using EVC configuration for CE facing AC? Please post your AC port configuration.

CreatePlease to create content
Content for Community-Ad

Cisco COVID-19 Survey