09-24-2013 02:24 AM
hello all
i need to get up an L2VPN between 2 switch ME-3600X-24FS-M
i think the config is fine all show are OK
but i cant L2 link doesnt work, no ping between 2 CE
here the show
MES.M20.thn.icosnet.net#sho mpls L2transport vc 102 detail
Local interface: Gi0/12 up, line protocol up, Eth VLAN 102 up
Interworking type is Ethernet
Destination address: 10.255.255.11, VC ID: 102, VC status: up
Output interface: Gi0/11, imposed label stack {88 27}
Preferred path: not configured
Default path: active
Next hop: 172.16.33.1
Create time: 21:19:46, last status change time: 21:19:46
Last label FSM state change time: 21:19:46
Signaling protocol: LDP, peer 10.255.255.11:0 up
Targeted Hello: 10.255.255.10(LDP Id) -> 10.255.255.11, LDP is UP
Status TLV support (local/remote) : enabled/supported
LDP route watch : enabled
Label/status state machine : established, LruRru
Last local dataplane status rcvd: No fault
Last BFD dataplane status rcvd: Not sent
Last BFD peer monitor status rcvd: No fault
Last local AC circuit status rcvd: No fault
Last local AC circuit status sent: No fault
Last local PW i/f circ status rcvd: No fault
Last local LDP TLV status sent: No fault
Last remote LDP TLV status rcvd: No fault
Last remote LDP ADJ status rcvd: No fault
MPLS VC labels: local 28, remote 27
Group ID: local 0, remote 0
MTU: local 1500, remote 1500
Remote interface description:
Sequencing: receive disabled, send disabled
Control Word: On (configured: autosense)
Dataplane:
SSM segment/switch IDs: 4117/4116 (used), PWID: 1
VC statistics:
transit packet totals: receive 35, send 8815
transit byte totals: receive 3090, send 602000
transit packet drops: receive 0, seq error 0, send 0
MES.M20.thn.icosnet.net# sho xconnect all
Legend: XC ST=Xconnect State S1=Segment1 State S2=Segment2 State
UP=Up DN=Down AD=Admin Down IA=Inactive
SB=Standby HS=Hot Standby RV=Recovering NH=No Hardware
XC ST Segment 1 S1 Segment 2 S2
------+---------------------------------+--+---------------------------------+--
UP pri ac Gi0/12:102(Eth VLAN) UP mpls 10.255.255.11:102 UP
MES.M20.thn.icosnet.net#sho mpls ldp neighbor
Peer LDP Ident: 10.255.255.1:0; Local LDP Ident 10.255.255.10:0
TCP connection: 10.255.255.1.646 - 10.255.255.10.57123
State: Oper; Msgs sent/rcvd: 1476/1480; Downstream
Up time: 21:24:44
LDP discovery sources:
GigabitEthernet0/11, Src IP addr: 172.16.33.1
Addresses bound to peer LDP Ident:
193.251.154.130 196.41.228.193 10.255.255.1 195.59.77.2
172.16.44.1 172.16.44.249 172.16.44.13 172.16.33.1
1.1.1.1
Peer LDP Ident: 10.255.255.11:0; Local LDP Ident 10.255.255.10:0
TCP connection: 10.255.255.11.61641 - 10.255.255.10.646
State: Oper; Msgs sent/rcvd: 1484/1480; Downstream
Up time: 21:20:23
LDP discovery sources:
Targeted Hello 10.255.255.10 -> 10.255.255.11, active, passive
Addresses bound to peer LDP Ident:
172.31.3.202 10.255.255.11 172.16.33.6
regards.
09-30-2013 02:56 AM
Hello Hamou,
Would you be so kind to capture from both sides of PW:
# show version
# show mpls l2 vc 102 detail
Thank you
--
Best regards,
Dmitry Skotnikov
10-30-2013 07:22 AM
Hello Hamou,
Have you tried changing the interworking type please?
adam
10-30-2013 05:41 PM
Are you using EVC configuration for CE facing AC? Please post your AC port configuration.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: