06-18-2017 03:08 AM
Dear all,
Is there anyone that manage to implement the above.
Topology for the open ring
PE1=>Gi0/0/9 ASR920 Gi0/0/8 => Gi0/3 ME3400EG Gi0/4 => PE2
test-asr920#show rep topology
REP Segment 10
Warning: REP detects a segment failure, topology may be incomplete
test-asr920#show rep topology
BridgeName PortName Edge Role
---------------- ---------- ---- ----
test-asr920 Gi0/0/8 Sec Alt
test-asr920 Gi0/0/9 Fail
test-asr920#show rep topology
REP Segment 10
Warning: REP detects a segment failure, topology may be incomplete
BridgeName PortName Edge Role
---------------- ---------- ---- ----
upper-9000 Gi0/4 Pri* Open
upper-9000 Gi0/3 Open
test-asr920 Gi0/0/8 Sec Alt
test-asr920#
from my tests it seems that there is a problem with the key
upper-9000#show rep topology
REP Segment 10
BridgeName PortName Edge Role
---------------- ---------- ---- ----
upper-9000 Gi0/4 Pri* Open
upper-9000 Gi0/3 Open
test-asr920 Gi0/0/8 Sec Alt
upper-9000#
========================
test-asr920#show int gigabitEthernet 0/0/8 rep detail
GigabitEthernet0/0/8 REP enabled
Segment-id: 10 (Segment)
PortID: 000F00FEC8D0553F
Preferred flag: No
Operational Link Status: TWO_WAY
Current Key: 000F00FEC8D0553F339B
Port Role: Alternate
Blocked VLAN: 1-4094
Admin-vlan: 1
Preempt Delay Timer: disabled
LSL Ageout Timer: 5000 ms
LSL Ageout Retries: 5
Configured Load-balancing Block Port: none
Configured Load-balancing Block VLAN: none
STCN Propagate to: none
LSL PDU rx: 75122, tx: 131937
HFL PDU rx: 41, tx: 41
BPA TLV rx: 5170, tx: 65210
BPA (STCN, LSL) TLV rx: 0, tx: 28
BPA (STCN, HFL) TLV rx: 0, tx: 28
EPA-ELECTION TLV rx: 22329, tx: 22329
EPA-COMMAND TLV rx: 0, tx: 0
EPA-INFO TLV rx: 16387, tx: 16933
test-asr920#show int gigabitEthernet 0/0/9 rep detail
GigabitEthernet0/0/9 REP enabled
Segment-id: 10 (Edge No-Neighbor)
PortID: 001000FEC8D0553F
Preferred flag: No
Operational Link Status: NO_NEIGHBOR
Current Key: 001000FEC8D0553F4DBC
Port Role: Open
Blocked VLAN: <empty>
Admin-vlan: 1
Preempt Delay Timer: disabled
LSL Ageout Timer: 5000 ms
LSL Ageout Retries: 5
Configured Load-balancing Block Port: none
Configured Load-balancing Block VLAN: none
STCN Propagate to: none
EFD State : Disabled
LSL PDU rx: 0, tx: 0
HFL PDU rx: 1, tx: 1
BPA TLV rx: 0, tx: 0
BPA (STCN, LSL) TLV rx: 0, tx: 0
BPA (STCN, HFL) TLV rx: 0, tx: 0
EPA-ELECTION TLV rx: 0, tx: 0
EPA-COMMAND TLV rx: 0, tx: 0
EPA-INFO TLV rx: 0, tx: 0
test-asr920#
Best regards
07-09-2020 07:03 PM
Were you able to make some progress on this?
Did you want to share your topology DIAGRAM?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide