cancelar
Mostrando los resultados de 
Buscar en lugar de 
Quiere decir: 
cancel
11427
Visitas
30
ÚTIL
19
Respuestas

Error AP 1832i

Hola, 

 

En la oficina un AP cisco 1832  (AIR – AP1832I-A-K9 / 1832 series 802.11ac dual Access point )

 

dejo de funcionar y cuando arranca entrega el siguiente error : L2 Error detected!

 

Anexo un extracto del  log de boot :

 

(RNAQ-C7) # bootipq
Specified BOOT: part2

Booting from part2

Read 1024 bytes from volume part2 to 45000000
Read 34741202 bytes from volume part2 to 45000000
Signature returns 0
Image signing verification success, continue to run...
Using machid 0x1260 from environment

Starting image ...

[01/01/1970 00:00:00.0000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5387d
[01/01/1970 00:00:00.0000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[01/01/1970 00:00:00.0000] Machine: Cisco Systems 11ac Wave2 Wifi Access Point
[01/01/1970 00:00:00.0000] Memory policy: ECC disabled, Data cache writealloc
[01/01/1970 00:00:00.0000] Kernel command line: ubi.mtd=0 crashkernel=30M@1280M console=ttyHSL1,9600n8 activepart=part2 activeboot=0 wdgtriggered=0
[01/01/1970 00:00:00.1500] CPU1: Booted secondary processor
[01/01/1970 00:00:20.4038] msm_serial_hs: probe of msm_serial_hs.0 failed with error -2
[01/01/1970 00:00:21.0736] buginf tty flushing thread started, ttyport=ef521090
[01/01/1970 00:00:25.7121] msm_hsusb_host msm_hsusb_host: unable to find transceiver
[01/01/1970 00:00:25.8421] watchdog: only one watchdog can use /dev/watchdog
[01/01/1970 00:00:25.9120] watchdog: error registering /dev/watchdog (err=-16)
[*01/01/1970 00:00:26.0920] buginf() enabled.

Welcome to Cisco.

.......

.....}...

 

[*09/25/2018 05:23:22.3383] [Flash] : Ignore Module param
[*09/25/2018 05:23:22.3483] ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0
[*09/25/2018 05:23:22.3683] ol_transfer_bin_file: Downloading firmware file: AR900B/hw.2/athwlan.bin
[*09/25/2018 05:23:23.4580] Startup Mode-0 set
[*09/25/2018 05:23:23.4580] HTC Service:0x0300 ep:1 TX flow control disabled
[*09/25/2018 05:23:23.4680] HTC Service:0x0100 ep:2 TX flow control disabled
[*09/25/2018 05:23:23.4680] Firmware_Build_Number:84
[*09/25/2018 05:23:23.4680] host/RAM_fw Build Ver Mismatch: H:0x47, F:0x54 !
[*09/25/2018 05:23:23.4680] num_rf_chain:0x00000004 ht_cap_info:0x0000185b vht_cap_info:0x339b79b2 vht_supp_mcs:0x0000ffea
[*09/25/2018 05:23:23.4680]
[*09/25/2018 05:23:23.4680] RES CFG Support wmi_service_bitmap 9778
[*09/25/2018 05:23:23.4680]
[*09/25/2018 05:23:23.4680] Sending Ext resource cfg: HOST PLATFORM as 0 and fw_feature_bitmap as 10 to TGT
[*09/25/2018 05:23:23.4680] Mesh Supported
[*09/25/2018 05:23:24.6676] pid 1424's current affinity mask: 3
[*09/25/2018 05:23:24.6676] pid 1424's new affinity mask: 1

[09/25/2018 05:23:33.4848] L2 Error detected!
[09/25/2018 05:23:33.4848] L2ESR = 0x00010001
[09/25/2018 05:23:33.4848] L2ESYNR0 = 0x300085d0
[09/25/2018 05:23:33.4848] L2ESYNR1 = 0x1022500a
[09/25/2018 05:23:33.4848] L2EAR0 = 0x884c8a68
[09/25/2018 05:23:33.4848] L2EAR1 = 0x00000002
[09/25/2018 05:23:33.4848] CPU bitmap = 0x1

 

Alguien sabe como solucionar esto ??

 

Atte. Gabriel

19 RESPUESTAS 19

Hola

Parece que el IOS se daño o esta corrupto, has intentado actualizar la imagen? adicional puedes abrir un caso con el Cisco TAC para brindarte mas claridad. 

 

Saludos 




>> Marcar como útil o contestado, si la respuesta resolvió la duda, esto ayuda a futuras consultas de otros miembros de la comunidad. <<

Hola ...

Gracias por tu respuesta, lo que hizo antes fue hacer un reset de fabrica  pero tampoco tuvo resultado, luego trate de bajar la versión de firmware pero ahora Cisco solicita un contrato y estamos gestionando eso para hacer el update del firmware.

 

Atte. Gabriel 

Muchas gracias Gabriel por el update, nos mantendremos pendientes una vez se logre actualizar la imagen.

 

Saludos 




>> Marcar como útil o contestado, si la respuesta resolvió la duda, esto ayuda a futuras consultas de otros miembros de la comunidad. <<

Edwin Portillo
Spotlight
Spotlight

@GabrielMunoz9150 deberías hacer lo que te sugiere @Julio E. Moisa actualizar IOS o probar con un reset de fábrica y verificar el funcionamiento:

 

https://bit.ly/2XjfNwq 

 

Hola, estamos esperando la gestión del contrato que solicita cisco para descargar el firmware  y actualizarlo..

 

Atte. Gabriel

 

 

 

Excelente me da gusto saberlo. ¡Enhorabuena!

Hola, 

cargamos el firmware con el siguiente comando 

 

 

tftpboot  AIR-AP1830-K9-ME-8-3-150-0.zip

 

...pero dio el mismo error ...

¿ existe algún comando adicional para limpiar por completo la configuración antigua ??

Del log que mostraste al inicio, el AP esta en uboot, desde ahi no vas poder cargar una nueva imagen. 

El AP esta cargando directamente a uboot?

Podrias mandar el console log del AP booteando? - si la imagen esta corrupta podermos cargar la imagen q esta en la particion 2. 

 

Saludos,

Rafael - TAC 

Saludos,
Rafael - TAC

Hola, aquí va el LOG de la consola ...

¿que comando debemos ejecutar para poder cargar correctamente el firmware desde U-Boot ?

 

desde ya gracias por tu ayuda y tiempo

 

 

========================================

U-Boot 2012.07 (btldr release 25) (Aug 19 2016 - 13:54:18)

 

This product contains some software licensed under the

"GNU General Public License, version 2" provided with

ABSOLUTELY NO WARRANTY under the terms of

"GNU General Public License, version 2", available here:

http://www.gnu.org/licenses/old-licenses/gpl-2.0.html

 

DRAM:  1 GiB

NAND (ONFI): Detected SPANSION S34MS02G2 [256 MiB]

SF: Detected Macronix MX25U3235F [4 MiB]

MFG data loaded

Scanning shenv data blocks

Total valid parts=4

Active shenv part[0:0], write_counter=101

PCI0 Link Intialized

PCI1 Link Intialized

Net:

PHY ID = 0x4dd074, eth0 found AR8033 PHY

PHY ID = 0x4dd074, eth1 found AR8033 PHY

Valid I2C chip addresses: 51 52

AP 1832/1852 detected...

Power Type: 802.3at POE detected...

Signature returns 0

BL signing verification success, continue to run...

Auto boot mode, use bootipq directly

Hit ESC key to stop autoboot:  0

Specified BOOT: part2

 

Booting from part2

 

Read 1024 bytes from volume part2 to 45000000

Read 34741202 bytes from volume part2 to 45000000

Signature returns 0

Image signing verification success, continue to run...

Using machid 0x1260 from environment

 

Starting image ...

 

[01/01/1970 00:00:00.0000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), c                                                                                        r=10c5387d

[01/01/1970 00:00:00.0000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruc                                                                                        tion cache

[01/01/1970 00:00:00.0000] Machine: Cisco Systems 11ac Wave2 Wifi Access Point

[01/01/1970 00:00:00.0000] Memory policy: ECC disabled, Data cache writealloc

[01/01/1970 00:00:00.0000] Kernel command line: ubi.mtd=0 crashkernel=30M@1280M                                                                                         console=ttyHSL1,9600n8 activepart=part2 activeboot=0 wdgtriggered=0

[01/01/1970 00:00:00.1500] CPU1: Booted secondary processor

[01/01/1970 00:00:20.4038] msm_serial_hs: probe of msm_serial_hs.0 failed with e                                                                                        rror -2

[01/01/1970 00:00:21.0736] buginf tty flushing thread started, ttyport=ef4e2890

[01/01/1970 00:00:25.7021] msm_hsusb_host msm_hsusb_host: unable to find transce                                                                                        iver

[01/01/1970 00:00:25.8221] watchdog: only one watchdog can use /dev/watchdog

[01/01/1970 00:00:25.8920] watchdog: error registering /dev/watchdog (err=-16)

[*01/01/1970 00:00:26.0720] buginf() enabled.

 

Welcome to Cisco.

 

Usage of this device is governed by Cisco's End User License Agreement,

available at:

http://www.cisco.com/c/en/us/td/docs/general/warranty/English/EU1KEN_.html.

 

 

             Restricted Rights Legend

 

Use, duplication, or disclosure by the Government is subject to

restrictions as set forth in subparagraph (c) of the Commercial

Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and

subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

 

            Cisco Systems, Inc.

            170 West Tasman Drive

            San Jose, California 95134-1706

 

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

 

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

 

If you require further assistance please contact us by sending email to

export@cisco.com.

 

 

This product contains some software licensed under the

"GNU General Public License, version 2" provided with

ABSOLUTELY NO WARRANTY under the terms of

"GNU General Public License, version 2", available here:

http://www.gnu.org/licenses/old-licenses/gpl-2.0.html

 

 

This product contains some software licensed under the

"GNU Library General Public License, version 2" provided

with ABSOLUTELY NO WARRANTY under the terms of "GNU Library

General Public License, version 2", available here:

http://www.gnu.org/licenses/old-licenses/lgpl-2.0.html

 

 

This product contains some software licensed under the

"GNU Lesser General Public License, version 2.1" provided

with ABSOLUTELY NO WARRANTY under the terms of "GNU Lesser

General Public License, version 2.1", available here:

http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html

 

 

This product contains some software licensed under the

"GNU General Public License, version 3" provided with

ABSOLUTELY NO WARRANTY under the terms of

"GNU General Public License, Version 3", available here:

http://www.gnu.org/licenses/gpl.html.

 

[*01/01/1970 00:00:26.0820] Made it into bootsh: Dec  6 2016 01:58:15

[*01/01/1970 00:00:26.0820] bootsh build T-b437e13e36d7f9e45776ba1dd26ebfdf25d90                                                                                        348-gb437e13e-vipendya

[*01/01/1970 00:00:27.6015] /init: reading file /storage/config: No such file or                                                                                         directory

init started: BusyBox v1.20.2 (2016-12-06 01:20:00 PST)

/usr/bin/serial_logincheck: reading file /storage/config: No such file or direct                                                                                        ory

 

 

 

User Access Verification

Username: [*01/01/1970 00:00:29.4509] Active version: 8.2.141.0

[*01/01/1970 00:00:29.4509] Backup version: 8.2.111.0

[*01/01/1970 00:00:29.6109] AP1852I

[*01/01/1970 00:00:29.7009] nss_driver - Turbo Support 1

[*01/01/1970 00:00:29.7009] Supported Frequencies - 110Mhz 550Mhz 733Mhz

[*01/01/1970 00:00:30.1607] Current value of FACTORY_RESET=0

[*01/01/1970 00:00:30.1707] Last reload time: Sep 25 05:23:17 2018

[*09/25/2018 05:23:17.0000] Setting system time Tue Sep 25 05:23:17 UTC 2018

[*09/25/2018 05:23:17.0699] device wired0 entered promiscuous mode

[*09/25/2018 05:23:17.1399] device wired1 entered promiscuous mode

[*09/25/2018 05:23:17.1399]

[*09/25/2018 05:23:17.1399] phy_value=0: org="0x1000" phy_reg="0x1800"

[*09/25/2018 05:23:17.4798] stile_lm_ft_corsica: module license [09/25/2018 05:2                                                                                        3:17.4998] stile module dp init successfully

[09/25/2018 05:23:17.5998] NBAR Label:BLD_MCP_DEV_LATEST_20150424_123021 NBAR VE                                                                                        RSION:module build date: Nov  4 2015 at 14:26:22

'Copyright (c) 2014-2015 by cisco Systems, Inc.' taints kernel.

[*09/25/2018 05:23:17.4998] stile_lm_dp_corsica: module license 'Copyright (c) 2                                                                                        014-2015 by cisco Systems, Inc.' taints kernel.

[*09/25/2018 05:23:18.1097]

[*09/25/2018 05:23:18.1196] boot 4 build T-b437e13e36d7f9e45776ba1dd26ebfdf25d90                                                                                        348-gb437e13e-vipendya board corsica mac 00:B0:E1:A4:38:80

[*09/25/2018 05:23:18.1196] Module: aptrace  .text=0xbf000000        data=0xbf00                                                                                        69c0        bss=0xbf006cf8

[*09/25/2018 05:23:18.1196] Module: qca_nss_gmac  .text=0xbf00f000        data=0                                                                                        xbf015b40        bss=0xbf016000

[*09/25/2018 05:23:18.1196] Module: qca_nss_drv  .text=0xbf01f000        data=0x                                                                                        bf0367b0        bss=0xbf037560

[*09/25/2018 05:23:18.1196] Module: qca_nss_capwapmgr  .text=0xbf053000        d                                                                                        ata=0xbf056b90        bss=0xbf056ce0

[*09/25/2018 05:23:18.1196] Module: nssmgrctl  .text=0xbf05c000        data=0xbf                                                                                        05d728        bss=0xbf05da4c

[*09/25/2018 05:23:18.1196] Module: proclikefs  .text=0xbf063000        data=                                                                                                bss=0xbf063b40

[*09/25/2018 05:23:18.1196] Module: stile_lm_ft  .text=        data=        bss=

[*09/25/2018 05:23:18.1196] Module: stile_lm_dp  .text=        data=        bss=

[*09/25/2018 05:23:18.1196] Module: qca_nss_profile_drv  .text=0xbf8ce000                                                                                                data=0xbf8cf324        bss=0xbf8cf498

[*09/25/2018 05:23:18.4595] Last reload reason : 0: unknown

[*09/25/2018 05:23:19.6892] adf: module license 'Proprietary' taints kernel.

[*09/25/2018 05:23:19.6992] asf: module license 'Proprietary' taints kernel.

[*09/25/2018 05:23:19.6992] ath_hal: module license 'Proprietary' taints kernel.

[*09/25/2018 05:23:19.7092] ath_dfs: module license 'Proprietary' taints kernel.

[*09/25/2018 05:23:19.7191] ath_rate_atheros: module license 'Proprietary' taint                                                                                        s kernel.

[*09/25/2018 05:23:19.7191] ath_dev: module license 'Proprietary' taints kernel.

[*09/25/2018 05:23:19.7491]

[*09/25/2018 05:23:19.7491] __ol_ath_attach() Allocated scn c52c0480

[*09/25/2018 05:23:19.7591] Chip id: 0x9, chip version: 0x1000000

[*09/25/2018 05:23:19.7591]

[*09/25/2018 05:23:19.7591]  Target Version is 1000000

[*09/25/2018 05:23:19.7591]

[*09/25/2018 05:23:19.7591]  Flash Download Address  c0000

[*09/25/2018 05:23:19.7591] ol_transfer_bin_file: flash data file defined

[*09/25/2018 05:23:19.7591] Cal location [0]: 00000000

[*09/25/2018 05:23:19.7591]

[*09/25/2018 05:23:19.7591]  Wifi0 NAND FLASH Select OFFSET 0x1000

[*09/25/2018 05:23:19.7791] qc98xx_verify_checksum: flash checksum passed: 0x56c                                                                                        5

[*09/25/2018 05:23:19.7791] ol_transfer_bin_file 4017: Download Flash data len 1                                                                                        2064

[*09/25/2018 05:23:19.8091]

[*09/25/2018 05:23:19.8091]  Board data initialized

[*09/25/2018 05:23:19.8491] ol_ath_download_firmware :First OTP download and Exe                                                                                        cute is good address:0xa000 return param 4660

[*09/25/2018 05:23:19.8491] ol_ath_download_firmware:##Board Id 8 , CHIP Id 1

[*09/25/2018 05:23:19.8491] ol_transfer_bin_file: Board Data File download to ad                                                                                        dress=0xc0000 file name=AR900B/hw.2/boardData_AR900B_CUS260_negative_pwr_offset_                                                                                        2G_v2_008.bin

[*09/25/2018 05:23:19.9191]

[*09/25/2018 05:23:19.9191]  [Flash] : Ignore Module param

[*09/25/2018 05:23:19.9291] ol_ath_download_firmware : Second OTP download and E                                                                                        xecute is good, param=0x0

[*09/25/2018 05:23:19.9491] ol_transfer_bin_file: Downloading firmware file: AR9                                                                                        00B/hw.2/athwlan.bin

[*09/25/2018 05:23:21.0487] Startup Mode-0 set

[*09/25/2018 05:23:21.0487] HTC Service:0x0300 ep:1 TX flow control disabled

[*09/25/2018 05:23:21.0587] HTC Service:0x0100 ep:2 TX flow control disabled

[*09/25/2018 05:23:21.0587] Firmware_Build_Number:84

[*09/25/2018 05:23:21.0587] host/RAM_fw Build Ver Mismatch: H:0x47, F:0x54 !

[*09/25/2018 05:23:21.0587] num_rf_chain:0x00000004  ht_cap_info:0x0000185b  vht                                                                                        _cap_info:0x339a79b2  vht_supp_mcs:0x0000ffea

[*09/25/2018 05:23:21.0587]

[*09/25/2018 05:23:21.0587]  RES CFG Support wmi_service_bitmap 9778

[*09/25/2018 05:23:21.0587]

[*09/25/2018 05:23:21.0587]  Sending Ext resource cfg: HOST PLATFORM as 0 and fw                                                                                        _feature_bitmap as 10 to TGT

[*09/25/2018 05:23:21.0587] Mesh Supported

[*09/25/2018 05:23:21.1287] wmi_ready_event_rx:  WMI UNIFIED READY event

[*09/25/2018 05:23:21.1387] ACS not enabled

[*09/25/2018 05:23:21.1387] ol_ath_thermal_mitigation_attach: --

[*09/25/2018 05:23:21.1387]

[*09/25/2018 05:23:21.1387] __ol_ath_attach() Allocated scn c44c0480

[*09/25/2018 05:23:21.1587] Chip id: 0x9, chip version: 0x1000000

[*09/25/2018 05:23:21.1587]

[*09/25/2018 05:23:21.1587]  Target Version is 1000000

[*09/25/2018 05:23:21.1587]

[*09/25/2018 05:23:21.1587]  Flash Download Address  c0000

[*09/25/2018 05:23:21.1587] ol_transfer_bin_file: flash data file defined

[*09/25/2018 05:23:21.1587] Cal location [1]: 00004000

[*09/25/2018 05:23:21.1587]

[*09/25/2018 05:23:21.1587]  wifi1 NAND FLASH Select OFFSET 0x5000

[*09/25/2018 05:23:21.1787] qc98xx_verify_checksum: flash checksum passed: 0x796                                                                                        7

[*09/25/2018 05:23:21.1787] ol_transfer_bin_file 4017: Download Flash data len 1                                                                                        2064

[*09/25/2018 05:23:21.1987]

[*09/25/2018 05:23:21.1987]  Board data initialized

[*09/25/2018 05:23:21.2387] ol_ath_download_firmware :First OTP download and Exe                                                                                        cute is good address:0x9c00 return param 4660

[*09/25/2018 05:23:21.2387] ol_ath_download_firmware:##Board Id 7 , CHIP Id 1

[*09/25/2018 05:23:21.2387] ol_transfer_bin_file: Board Data File download to ad                                                                                        dress=0xc0000 file name=AR900B/hw.2/boardData_AR900B_CUS239_negative_pwr_offset_                                                                                        5G_v2_007.bin

[*09/25/2018 05:23:21.3087]

[*09/25/2018 05:23:21.3087]  [Flash] : Ignore Module param

[*09/25/2018 05:23:21.3286] ol_ath_download_firmware : Second OTP download and E                                                                                        xecute is good, param=0x0

[*09/25/2018 05:23:21.3386] ol_transfer_bin_file: Downloading firmware file: AR9                                                                                        00B/hw.2/athwlan.bin

[*09/25/2018 05:23:22.0484] FWLOG: [34928] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1                                                                                        e, 0x94c, 0x94c, 0x0 )

[*09/25/2018 05:23:22.0484] FWLOG: [34928] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x                                                                                        1e, 0x94c, 0x94c, 0x0 )

[*09/25/2018 05:23:22.0484] FWLOG: [34928] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x                                                                                        1e, 0x94c, 0x94c, 0x0 )

[*09/25/2018 05:23:22.0484] FWLOG: [34928] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x                                                                                        1e, 0x94c, 0x94c, 0x0 )

[*09/25/2018 05:23:22.4383] Startup Mode-0 set

[*09/25/2018 05:23:22.4383] HTC Service:0x0300 ep:1 TX flow control disabled

[*09/25/2018 05:23:22.4383] HTC Service:0x0100 ep:2 TX flow control disabled

[*09/25/2018 05:23:22.4383] Firmware_Build_Number:84

[*09/25/2018 05:23:22.4383] host/RAM_fw Build Ver Mismatch: H:0x47, F:0x54 !

[*09/25/2018 05:23:22.4383] num_rf_chain:0x00000004  ht_cap_info:0x0000185b  vht                                                                                        _cap_info:0x339b79b2  vht_supp_mcs:0x0000ffea

[*09/25/2018 05:23:22.4383]

[*09/25/2018 05:23:22.4383]  RES CFG Support wmi_service_bitmap 9778

[*09/25/2018 05:23:22.4383]

[*09/25/2018 05:23:22.4383]  Sending Ext resource cfg: HOST PLATFORM as 0 and fw                                                                                        _feature_bitmap as 10 to TGT

[*09/25/2018 05:23:22.4383] Mesh Supported

[*09/25/2018 05:23:24.6376] pid 1424's current affinity mask: 3

[*09/25/2018 05:23:24.6376] pid 1424's new affinity mask: 1

[09/25/2018 05:23:32.4552] L2 Error detected!

[09/25/2018 05:23:32.4952]      L2ESR    = 0x00010001

[09/25/2018 05:23:32.5451]      L2ESYNR0 = 0x300085d4

[09/25/2018 05:23:32.5951]      L2ESYNR1 = 0x1022500a

[09/25/2018 05:23:32.6551]      L2EAR0   = 0x880c8a68

[09/25/2018 05:23:32.7051]      L2EAR1   = 0x00000002

[09/25/2018 05:23:32.7551]      CPU bitmap = 0x1

 

No estoy seguro se copio todo el output. Pudes copiarlo y pegarlo en un archivo.

 

Rafael 

Saludos,
Rafael - TAC

Hola,

 

Adjunto LOG para facilitar su lectura.

 

 

 

Atte. Gabriel 

Hola a todos :),

 

 

Se descargo el firmware desde el sitio de Cisco, se habilito un server tftp en la misma red que AP cisco  y ejecuto el siguiente comando :

 

tftpboot  AIR-AP1830-K9-ME-8-3-150-0.zip

 

descargo el archivo ... todos felices pero al momento de boot dio el mismo error .. :(

 

¿hay que limpiar una configuración ?

 

Atte. Gabriel 

que prompt te dio el AP?

Saludos,
Rafael - TAC