Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
Hi,I have come across a lab setup MP-BGP Inter-AS VPNv4. In this setup MPLS is running between two ASBR and MP-BGP vpnv4 peering is made between to RR. By this both the ISP can recevice all the vpnv4 prefixes. IS THIS A BEST PRACTICE ?
HiIf i have in the mpls NET cisco routers that acts as route-reflector witch platforn and IOS support vpls sig with BGP?TnxSent from Cisco Technical Support Android App
Hi Guys,I am working on one Enterprise network design where virutualization is main concern.so we decided for EVN but unfVortunately only 32 EVN are supported from cisco. We moved back to Old VRF technology.Requirement for VRF is around 600 in number...
hi All,Need to understand the signifiniace of connecting PE to PE router and then to P router. Do i have to have all the PE LDP to only P router or i can have LDP neigbour with my PE device.PE 4 should have LDP with PE2 or directly to P1 router
I had configured a sham link between ce-----pe----shamlink-------pe---------ceiam getting the ospf neighbourship up but suddenly it is getting down.Please share you views to clear this problem.Thanks in advance.Ma...
I know the 6500 isn't suggested to be used for VPLS, that the 7600s are, but I have found forums stating that it is possible. I found, thus far, a SIP600 card, a SUP720B, or greater, could make the 6500 capable of supporting VPLS.Please help by expl...
Hello,Is it necessary to put a firewall between your MPLS site or is it over kill if placing a firewall that’s already using MPLS VPN between sites?Thank you all in advanceJepoy
Hello,I am testing VPLS service on the ASR1001. I have three of them directly connected in a full mesh with autodiscovery mode. On the first two ASR1K I have a switch connected in order to test the end-to-end reachability.The VCs are in UP state, ICM...
Communication between Site A and Site B was through MPLS/VPN network. EIGRP was used between PE and CE. There was also a backdoor link between CEs. Topology and configuration were in attached file.R1 can learn routes in Site B(prefix 192.168.50.50/32...
I have the following setupCE-PE-PE-CEI have setup a l2vpn with a vfi and bridge domain. Unicast is working fine, but I cannot get link local multicast. The CEs need to have OSPF adjacency without neighbor statements to make the PE-PE connection look ...
Hello,we have just rolled an MPLS network as service provider and will soon lunch services through it, to start with is l3vpn. I would like to find out what are the best practices for LDP setup such as would you recommend to have;- MD5 passwords fro...
Buenas dia, Amigos!I want to limit the speed of the MPLS Tunnel between two sites. I'm going to create a MPLS tunnel and apply"tunnel mpls traffic-eng bandwidth X"Can anybody answer me, it can really limit the speed or only reserve bandwidth?!Hasta l...
Hello,I'm currently deploying some ISR 1900 as MPLS hand off with xconnect and would like to do testing to make sure that the configuration is correct, but I can not find a way to force my customer facing interface in a up state without them plugging...
Hi,Would like to know which IOS version would support RSVP bundle messsages, generate and receive on cisco 7206 platform.Any help regarding this would be great.Thanks
How to troubleshoot this log:%PM-4-ERR_DISABLE_VP: elmi evc down error detected on Fa0/24, vlan 101. Putting in err-disable state. Thank you very much.upe11#sho ethern cfm domDomain Name: provider_domainLevel: 4 Total Services: 2 Services: Type Id...
