Hello All,
ios4------XRV9K1--------CSR2---------XRV9K3------ios5
When I try to commit config on XRV9K1 and XRV9K3 then I get the following error.
!!% Invalid argument: VPWS Preferred path fallback enable not supported on this system
ios4
----------------------------------
int gi0/0
ip address 100.10.10.4 255.255.255.0
no sh
XR9KV1
-----------------------
int gi0/0/0/0
l2transport
no sh
int gi0/0/0/1
ip address 100.10.20.1 255.255.255.0
no sh
int lo0
ip address 1.1.1.1 255.255.255.255
mpls ldp
exit
l2vpn
pw-class class1
encap mpls
preferred-path sr-te policy pol1
exit
exit
xconnect group group1
p2p p2p
int gi0/0/0/0
neighbor 3.3.3.3 pw-id 123
pw-class class1
exit
exit
router isis 1
net 49.0001.1111.1111.1111.00
is-type level-2
distribute link-state
address-family ipv4 unicast
router-id lo0
metric-style wide
no mpls ldp auto-config
segment-routing mpls
mpls traffic-eng router-id lo0
mpls traffic-eng level-2
advertise passive-only
exit
int gi0/0/0/1
point-to-point
address-family ipv4 unicast
exit
int lo0
passive
address-family ipv4 unicast
prefix-sid index 1
exit
XRV2
-----------------------
segment-routing mpls
connected-prefix-sid-map
address-family ipv4
2.2.2.2/32 index 2 range 1
exit
exit
int gi1
ip address 100.10.20.2 255.255.255.0
ip router isis 1
isis network point-to-point
no sh
int gi2
ip address 100.20.30.2 255.255.255.0
ip router isis 1
isis network point-to-point
no sh
int lo0
ip address 2.2.2.2 255.255.255.255
ip router isis 1
exit
router isis 1
net 49.0002.2222.2222.2222.00
is-type level-2
metric-style wide
segment-routing mpls
mpls traffic-eng router-id lo0
mpls traffic-eng level-2
distribute link-state
router-id lo0
exit
XRV3
-----------------------
int gi0/0/0/1
l2transport
no sh
int gi0/0/0/0
ip address 100.20.30.3 255.255.255.0
no sh
int lo0
ip address 3.3.3.3 255.255.255.255
exit
l2vpn
pw-class class1
encap mpls
preferred-path sr-te policy pol1
exit
exit
xconnect group group1
p2p p2p
int gi0/0/0/1
neighbor 1.1.1.1 pw-id 123
pw-class class1
exit
exit
router isis 1
net 49.0003.3333.3333.3333.00
is-type level-2
distribute link-state
address-family ipv4 unicast
router-id lo0
metric-style wide
segment-routing mpls
mpls traffic-eng router-id lo0
mpls traffic-eng level-2
exit
int gi0/0/0/1
point-to-point
address-family ipv4 unicast
exit
int gi0/0/0/0
point-to-point
address-family ipv4 unicast
exit
int lo0
passive
address-family ipv4 unicast
prefix-sid index 3
exit
ios5
-------------
int gi0/1
ip address 100.10.10.5 255.255.255.0
no sh
