cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other best practices.

5146
Views
0
Helpful
6
Replies

ACS 5.2 Cisco-AV-Pair Problem

Hi at all

i have a Problem with the cisco-av-pair string on the Cisco ACS and a SSID.

We  have here some SSID and some AD Groups. It was no Problem with the old  Cisco ACS 4.2. I have here configured the string: cisco-av-pair  ssid=myssid. The Clients have only rights to this ssid. It works without  Problems.

On the new ACS 5.2. I have here Problem to configure this.

My Configuration is a new Identity Policy.

Compound Condition:

Radius-Cisco -->cisco-av-pair-->equals-->myssid

But this string works not.

Did you have any ideas about this Problem.

My System:

Cisco ACS 5.2 with all new Patches

Cisco WLC newest Version

Thanks

regards

Andreas

1 ACCEPTED SOLUTION

Accepted Solutions

You could try a condition:

Called-Station-ID  ends-with ":0FFEN"

View solution in original post

6 REPLIES 6
jrabinow
Rising star

I think you need to match on the string that appears in the attribute. In this case. "ssid=myssid"

If you want to confirm what string should be used select: Monitoring and reports -> Launch Monitoring & Report Viewer

and then select Authentications -> RADIUS today

You should see a list of the requests including the ones you had tried. In the details column click on the icon and you will see the details of your RADIUS request. This includes the list of RADIUS attributes received. You can look at what is in the AV pair field and make sure a correct condition is specified

Hi jrabinow,

thanks for your Answer.

My Authorization Policy is with follow string:

RADIUS-Cisco:cisco-av-pair equals ssid=OFFEN

I can the in Other Attributes:

ACSVersion=acs-5.2.0.26-B.3075
ConfigVersionId=56
Device  Port=32769
RadiusPacketType=AccessRequest
Protocol=Radius
Service-Type=Framed
Framed-MTU=1300
Called-Station-ID=1c-17-d3-fc-9b-00:OFFEN
Airespace-Wlan-Id=7
Device  IP Address=10.99.11.16

OFFEN is my SSID.

In the Steps from the Report i can see:

regards

Andreas

15006  Matched Default Rule

15012  Selected Access Service -  DenyAccess

11019  Selected DenyAccess Service

11003  Returned RADIUS Access-Reject

from the steps can see that no Access Service is being matched. It is selecting the default rule.

A first step will be to look at the Service Selection Policy (Access Policies > Access Services > Service Selection Rules) and see why an access service is not being selected

I have make a Test with the "Airespace-WLAN-ID" Attribute.

I can configure a rule with

RADIUS-Cisco Airespace-Wlan-ID=7

This works. I can only connect to this Wlan-ID.

I have found this in the Other Attributes list.

ACSVersion=acs-5.2.0.26-B.3075

ConfigVersionId=56

Device  Port=32769

RadiusPacketType=AccessRequest

Protocol=Radius

Service-Type=Framed

Framed-MTU=1300

Called-Station-ID=1c-17-d3-fc-9b-00:OFFEN

Airespace-Wlan-Id=7

Device  IP Address=10.99.11.16

But i can not find only the name of the SSID, only in the String "Called-Station-ID..."

Is it possible that the ACS get not this Information from the WLC?

You could try a condition:

Called-Station-ID  ends-with ":0FFEN"

Hi Jrabinow,

thanks for your help. I have configured this condition and now it works.

regards

Andreas

Create
Recognize Your Peers
Content for Community-Ad

ISE Webinars


Miss a previous ISE webinar?
Never miss one again!

CiscoISE on YouTube