cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other best practices.

1370
Views
0
Helpful
1
Replies
Highlighted
Beginner

Cisco CSR1000v VPDN(like LNS) not working

Hi,

I am trying to migrate LNS function from a CISCO 4431 router to a CSR1000v virtual router, but the VPDN not working after migration. I am thinking about a bug or a software problem on the CSR1000v, but couldn't find a related topic on the bug search tool or release notes. Do someone have any idea?

 

I am keeping the same config including IP addresses.

- The l2tp tunnels establish between LAC and LNS

- The sites are able to establish PPPoE session to the new LNS router CSR1000v
- from the new LNS router, I can see routes installed (including LAN routes) from sites but I am not able to PING any of the sites WAN IPs from the LNS that are assigned IP addresses from the /24 subnet I configured in the LNS

-I opened debug on one of the site routers, I can see that it installed the IPCP route to the LNS as well. PPP session becomes up but after around 4 mins because of missed PPP keepalives PPP session become down like below logs. : 

 

Jun 3 21:26:34: Vi1 PPP: Phase is FORWARDING, Attempting Forward
*Jun 3 21:26:34: Vi1 PPP: Queue IPCP code[1] id[1]
*Jun 3 21:26:34: Vi1 PPP: Phase is ESTABLISHING, Finish LCP
*Jun 3 21:26:34: Vi1 PPP: Phase is UP
*Jun 3 21:26:34: Vi1 IPCP: Protocol configured, start CP. state[Initial]
*Jun 3 21:26:34: Vi1 IPCP: Event[OPEN] State[Initial to Starting]
*Jun 3 21:26:34: Vi1 IPCP: O CONFREQ [Starting] id 1 len 10
*Jun 3 21:26:34: Vi1 IPCP: Address 10.1.1.22 (0x03060A013216)
*Jun 3 21:26:34: Vi1 IPCP: Event[UP] State[Starting to REQsent]
*Jun 3 21:26:34: Vi1 PPP: Process pending ncp packets
*Jun 3 21:26:34: Vi1 IPCP: Redirect packet to Vi1
*Jun 3 21:26:34: Vi1 IPCP: I CONFREQ [REQsent] id 1 len 10
--More-- *Jun 3 21:26:34: Vi1 IPCP: Address 10.1.1.250 (0x03060A0132FA)
*Jun 3 21:26:34: Vi1 IPCP: O CONFACK [REQsent] id 1 len 10
*Jun 3 21:26:34: Vi1 IPCP: Address 10.1.1.250 (0x03060A0132FA)
*Jun 3 21:26:34: Vi1 IPCP: Event[Receive ConfReq+] State[REQsent to ACKsent]
*Jun 3 21:26:34: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up
*Jun 3 21:26:34: Vi1 IPCP: I CONFACK [ACKsent] id 1 len 10
*Jun 3 21:26:34: Vi1 IPCP: Address 10.1.1.22 (0x03060A013216)
*Jun 3 21:26:34: Vi1 IPCP: Event[Receive ConfAck] State[ACKsent to Open]
*Jun 3 21:26:34: Vi1 IPCP: State is Open
*Jun 3 21:26:34: Di1 IPCP: Install route to 10.1.1.250
*Jun 3 21:30:44: Vi1 PPP: Missed 5 keepalives, taking LCP down
*Jun 3 21:30:44: Vi1 PPP DISC: Missed too many keepalives
*Jun 3 21:30:44: Vi1 IPCP: Event[DOWN] State[Open to Starting]
*Jun 3 21:30:44: Vi1 IPCP: Event[CLOSE] State[Starting to Initial]
*Jun 3 21:30:44: Vi1 LCP: O TERMREQ [Open] id 2 len 4
*Jun 3 21:30:44: Vi1 LCP: Event[CLOSE] State[Open to Closing]
*Jun 3 21:30:44: Vi1 PPP: Phase is TERMINATING
*Jun 3 21:30:44: Vi1 LCP: Event[DOWN] State[Closing to Initial]
*Jun 3 21:30:44: Vi1 PPP: Phase is DOWN
*Jun 3 21:30:44: Di1 IPCP: Remove route to 10.1.1.250
*Jun 3 21:30:44: PPPoE : Shutting down client session

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
Beginner

Hi,

I found the problem was related to the license.

Thanks.

 

View solution in original post

1 REPLY 1
Highlighted
Beginner

Hi,

I found the problem was related to the license.

Thanks.

 

View solution in original post

Content for Community-Ad