09-05-2013 07:40 PM
HI,
I have installed my LMS 4.2 on the EXSi 5.0 recently,but today i find i can't log in the web ,it display as follows:
"
Forbidden
You don't have permission to access / on this server .
Additionally,a 403 Forbidden error was encountered while trying to use an ErrorDocument to handle the request.
"
for this scenriao,what's the reason?
could you help me ?
when i installed successful,i'm sure i can log in the web view.
my web browser is IE9.0.
Solved! Go to Solution.
09-05-2013 10:21 PM
Hi ,
Try to Regenerate SSL certificates: 1) Stop the daemons manager from CLI using /etc/init.d/dmgtd stop 2) Backup the following files found in /opt/CSCOpx/MDC/Apache/conf/ssl and then delete: server.crt server.csr server.key server.pk8 Under CLI go to "\opt\CSCOpx\MDC\Apache\" and then run ConfigSSL.pl by typed the following command on CLI. CSCOpx\MDC\Apache\perl configssl.pl -disable CSCOpx\MDC\Apache\perl configssl.pl -enable Then fill the certificate accordingly and restart daemons from CLI using netThanks-
start the daemon manager:
/etc/init.d/dmgtd stop
Afroz
09-05-2013 10:21 PM
Hi ,
Try to Regenerate SSL certificates: 1) Stop the daemons manager from CLI using /etc/init.d/dmgtd stop 2) Backup the following files found in /opt/CSCOpx/MDC/Apache/conf/ssl and then delete: server.crt server.csr server.key server.pk8 Under CLI go to "\opt\CSCOpx\MDC\Apache\" and then run ConfigSSL.pl by typed the following command on CLI. CSCOpx\MDC\Apache\perl configssl.pl -disable CSCOpx\MDC\Apache\perl configssl.pl -enable Then fill the certificate accordingly and restart daemons from CLI using netThanks-
start the daemon manager:
/etc/init.d/dmgtd stop
Afroz
10-11-2013 07:52 PM
Hi,
can you tell me how can i get into the cli page?
i login on the LMS from the console or through ssh, but i can't get these command?
10-11-2013 07:58 PM
Hi ,
you can get it through console or CLI as well. theh you need to type SHELL and then you should be able to run the command.
Thanks-
Afroz
10-11-2013 08:14 PM
ok, shell or shell_enable ?
i'll try it,thanks。
LMS02/sysadmin# ?
Exec commands:
application Application Install and Administration
clock Set the system clock
configure Enter configuration mode
copy Copy commands
debug Debugging functions (see also 'undebug')
delete Delete a file
dir List files on local filesystem
exit Exit from the EXEC
forceout Force Logout all the sessions of a specific system user
halt Shutdown the system
mkdir Create new directory
nslookup DNS lookup for an IP address or hostname
patch Install System or Application Patch
ping Ping a remote ip address
ping6 Ping a remote ipv6 address
reload Reboot the system
rmdir Remove existing directory
shell Access the shell by using the password
shell_enable Enable access to shell by setting password
show Show running system information
ssh SSH to a remote ip address
tech TAC commands
telnet Telnet to a remote ip address
terminal Set terminal line parameters
traceroute Trace the route to a remote ip address
undebug Disable debugging functions (see also 'debug')
write Write running system information
LMS02/sysadmin#
10-11-2013 08:42 PM
Hi ,
shell , if you know the password.
If you don't rememebe the shell paswword , you can reset it with shell_enable command.
Thanks-
Afroz
10-13-2013 10:14 PM
Hi,
After regenerate SSl Certificates, it works very well, thank you very much !
and in my case, it need to execute the command in the following directory,
[LMS01/root-ade Apache]# cd bin
[LMS01/root-ade bin]# ./ConfigSSL.pl -disable
SSL is already disabled
[LMS01/root-ade bin]#
[LMS01/root-ade bin]#
[LMS01/root-ade bin]# ./ConfigSSL.pl -enable
[LMS01/root-ade Apache]# cd bin
[LMS01/root-ade bin]# ./ConfigSSL.pl -disable
SSL is already disabled
[LMS01/root-ade bin]#
[LMS01/root-ade bin]#
[LMS01/root-ade bin]# ./ConfigSSL.pl -enable
Have a good day!
10-08-2017 06:01 AM
I have the same issue but can not type this command : ./ConfigSSL.pl -enable
How to solve it please?
Thanks
10-09-2017 12:32 AM
how to take buckup and to delete.
Thanks
04-02-2018 12:57 AM
HI AFROJ AHMAD
Backup the following files found in /opt/CSCOpx/MDC/Apache/conf/ssl
how do i backup i mean the cli command to backup the files?
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: