cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

13550
Views
20
Helpful
9
Replies

ACS 4.2 GUI Username and password

Hi,

I have setup cisco acs 4.2.1 i windows swerver 2008 and want to access through GUI, GUI interface is appear but I don't know the default  usrname and password. Please help.

Thanks

1 ACCEPTED SOLUTION

Accepted Solutions
VIP Mentor

Re: ACS 4.2 GUI Username and password

HI Hossain,

If u clicked locally means:

u must http://localhost:2002  logon locally on which u installed ACS.

u must use one of these HTML browsers:

•Microsoft Internet Explorer 6 Service Pack 1 and 5.5 for Windows-English and Japanese versions

•Microsoft Internet Explorer 7 Service Pack 2 for Windows Server 2003 and Service Pack 2 for Windows XP

•Mozilla Firefox 2.0 and 2.0.0.6

•Netscape Web Browser 7.0, 7.1, and 7.2 for Windows-English and Japanese versions1

Did u foloowed these steps:

http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/installation/guide/windows/install.html

Regards

9 REPLIES 9
VIP Mentor

ACS 4.2 GUI Username and password

ACS 4.2 GUI Username and password

Hi Sandeep choudhary,

Thanks for your reply. I am unable to login using your provided credential. username admin and password--> Password or --> password both i have used but no luck.

VIP Mentor

Re: ACS 4.2 GUI Username and password

HI Hossain,

Can u try these:

If its ur first time then :

Username: acsadmin

Password: default

After this the server will ask you to change the password. Please give it a try and let me know how it goes.

Reset ACSAdmin Password: To reset the password of the default GUI admin, use the acs reset-password command from the EXEC mode.

http://www.ciscopress.com/articles/article.asp?p=1671906&seqNum=7

Regards

Dont forget to rate helpful posts.

ACS 4.2 GUI Username and password

Hi Sandeep choudhary,

I have tried using the below but same result.

Username: acsadmin

Password: default

VIP Mentor

Re: ACS 4.2 GUI Username and password

Hi Hossain,

so lets find out the exact issue:

Which option did you click (checkbox), windows authentication or local

ACS only while installing ACS?

If u clicked locally then u may need to logon locally to the box first and create an ACS

account.

After installation, I believe you need to use http://127.0.0.1:2002 from the

device CSACS is installed on.

After that, I think you are prompted to setup a local username and

password for administration.

Try using the loopback address, and read the interface carefully for and

guidance on the creation of an admin account.

Regards

Dont forget to rate helpful posts.

Highlighted

ACS 4.2 GUI Username and password

Hi Sandeep choudhary,

During the setup i selected "check the ACS internal database only" radio button and finally automatic run http://127.0.0.1:2002 in IE.

VIP Mentor

Re: ACS 4.2 GUI Username and password

HI Hossain,

If u clicked locally means:

u must http://localhost:2002  logon locally on which u installed ACS.

u must use one of these HTML browsers:

•Microsoft Internet Explorer 6 Service Pack 1 and 5.5 for Windows-English and Japanese versions

•Microsoft Internet Explorer 7 Service Pack 2 for Windows Server 2003 and Service Pack 2 for Windows XP

•Mozilla Firefox 2.0 and 2.0.0.6

•Netscape Web Browser 7.0, 7.1, and 7.2 for Windows-English and Japanese versions1

Did u foloowed these steps:

http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/installation/guide/windows/install.html

Regards

ACS 4.2 GUI Username and password

Hi Sandeep choudhary,

After using Mozilla Firefox 2.0.0.6 and http://localhost:2002,

Now its working. Many thanks for your help. Previously i was tried from my remote machine.

VIP Mentor

ACS 4.2 GUI Username and password

Hi Hossain,

Glad that u resolved ur issue.

Thanks for rating.

Reagrds

Dont forget to rate all helpful posts.

CreatePlease to create content
Content for Community-Ad
July's Community Spotlight Awards