Network Management

This is a WS-C4510R+E with a Sup 7-E running 03.02.02.SG enterprise.I increased SNMP timeout to 10 seconds to no avail.The IC_Server.log is attached. Any ideas?-Jeff

Hello,I'm having problems installing LMS 4.2 in other partition. I have two operating system. One on C: Windows 7 Pro and One on D:Windows Server 2008,after installing it on Windows Server 2008, i'm able to access the server using the command net sta...

Hi All,I'm trying to add some 2800 series routers to our monitoring environment, but I can't get them discovered.Network setup:Mgmt Server <----> Cisco 2800 <----Private T1----> (e)Cisco 2800(i) <----> (p)Managed ServerOn the Mgmt Server I need to go...

Hi,I'm trying to raise a TAC for an issue with Ciscoworks and the Cisco Help Desk are asking for a serial number for the software.I can't find this serial number within the software and hence they won't accept me logging the call! I've asked to spea...

I need help configuring an email alert so that when a node (switch, router, etc) is unreachable, i will recieve an email notification.  So far i have tried creating an event set then notification group and then email subscription.  This does not seem...

Hi Guys,I am looking for kind of tool which can genrate reports for pair of devices considering - same config on both the devices / specific fields lets say ip route part should be same on both.My aim to make sure config for pair devices are same I k...

Does someone can lunch SSH and telnet too under topology service, I do all stuff mentionned in "Monitoring and Troubleshooting With CiscoWorks solution 4.0 without any result . I use Microsoft XP with IE7 and with Java 1.6.0_23 LAN Management Solutio...

Hello,we are planning to setup centralized network management sever to mange Cisco devices and Microsoft Severs, could anyone advice me what is the hardware requirements to handle all this??for Cisco devices I want to setup archiving and logging on t...

Hi everybody, Jack here,I have some basic questions about the Cisco IOS, could someone help me addressing some of them please? Any feedback would be greatly appreciated. Basically, I have two IP addresses assigned by our Cable ISP. From what I unders...

Hi all,We got the following error message on Ciscoworks LMS 2.6 on Solaris 5.9:{diskWatcher} - Avialable space in /var of server xxx is less than 10 percent.We stopped the Daemon Manager and delete some log files. After restarting the Daemon Manager ...

We have just installed lms 4.2 and are having problems collecting config and inventory from ws-svc-wism2-k9.  The response from TAC was that this is not supported.  And it also says this in http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_mana...

HiIn our network I am looking for solution in order to log any command that has been excuted on cisco devices by every user.It means, If user A excuted "show run int X/X" this command is to sent to log server or save in one server.What solution do yo...

                   This is a new install of LMS 4.2 evaluation.  I have a current install of LMS 3.2 which is working.   When I run an Add job for our core 6509 in Software Repository using cisco.com on the 3.2 LMS it works normally.  When I attempt ...

I want to set a collector between my C3845-IPbase-mz.124-3i router and one of my branches, the problem is I dont have my 3845 in source list it is just appear in the target devices ? but I want to set it as a source device  !!is it due to IOS version...

Hi,We r using BGP on our MPLS rtr..now we have added new network on the existing BGP setup.....but unable to show the same under BGP table.router bgp xxxxx bgp log-neighbor-changes neighbor 10.X.X.185 remote-as XX55 ! address-family ipv4  neighbor 10...