Network Management

Linksys router, problems with SNMP

Hello, We have several Linksys RVL200 routers out in the field. They work fine except now we want to enable SNMP to monitor bandwidth usage with PRTG Network Monitor. I’m having a problem with a few of these getting SNMP to work properly. I’ve co...

Is it possible to do EoX/PSIRT reporting against configs collected by another tool ?

I have been looking in vain for a tool which will allow us to feed a "show ver"/"show inv" into a tool and report on EoX/PSIRT status.We already have a configuration management tool deploying a copy of RME per customer would be an issue we would endu...

Resolved! Customizing HUM graphs

Hi,we have HUM 1.2. In all the graphs, the top Y axis value is related to the maximun measure showed by the graph, would it be possible to configure HUM for always showing a top value of 100?Thanks.

Resolved! Update on Cisco Works Open Database Schema Support dbviews document ?

Hello,does anyone know if an update on the document below is available somewherehttp://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/3.2/database_schema/guide/dbviews.htmlThe reason why I am asking is that I realised the docume...

LMS 3.2 - RME System Inventory Polling takes very long

Hi there,Environment: Solaris 10 (approx. 1400 devices managed)With scheduled RME System Inventory Polling Job at 01:00 am it ends 6,5 hours later.Looking into the Job-Log after about 53 minutes following messages are shown until job finish[ Fri Jun ...

View NetFlow Data in CiscoWorks LMS 3.1?

All,Can CiscoWorks LMS 3.1 view NetFlow data?If so, which LMS 3.1 product (IPM, RME, etc.) can view it?What products can view NetFlow data and create reports?How is IPM and NetFlow similar?Stephanie

File Format for export from Ciscoworks to ACS

Hi,I want to export devices from Ciscoworks lms 3.2 to ACS 4.1 with the cli-tooldcrcli expAcsBut, what is the file format I have to uselsattr gives me just the complete list of all cs-attributesthanks, William

Resolved! 403 forbidden error while trying to access CiscoWorks(LMA ver 2.6)

Hi,I am getting the follwing error in LMS ver 2.6 and not able to log in our cisco works server"You don't have permission to access /cwhp/LiaisonServlet on this server"Additionally, 403 forbidden error was encountered while trying to use an errordoc...

Resolved! CiscoWorks Usertracking problem

Hello,We are running CiscoWorks LMS 2.6 with Campus Manager 4.0.9. My problem is that although the Campus Data collection completes daily, user tracking aquisition has not run since 27/3/2010. I have also not been able to delete previous records (end...

Resolved! EEM - "action" not taken on another router with similar IOS

[Question origionally in "Network Infrastructure"->"WAN, Routing, Switch" forum. Asked to post it in here.]Hi !I been running a test script to verfiy EEM on our Cisco 6506 core switches. While the desired results are obtained on our Test 6506 devic...

DCR Add Device shows Duplicate Device Name

When manually adding some devices via DCR Device Management I get the "Duplicate Device Name" error.The names do not show in the DCR Device Management Selector. I have also done an Export of All Devices and the names are not in there either.I have co...

Topology map not working in LMS 3.1

Hi,I recently did a clean installation of LMS 3.1. The topology services is not working returning an error named "Failed to initialize: Java.lang.NumberFormatException: null"in the pop up window.Any help would be appreciatedwith thankssathappan

Query about accessing WiSM in Cat 6509 through session slot command

Hi,I have following setup in production.1.Cat 6509 having IOS 12.2(18)SXF82.WiSM module installed in slot 8 (Ver: 5.2.157.0)The setup is working smoothly , I am able to manage the WiSM module through GUI, Module console but not through Session Slot 8...

Resolved! Extended Ping command "Loose, Strict, Record, Timestamp, Verbose[none]:" explanation needed

One of my clients has a communication issue for an application installed on a server. He did an extended ping to the server to get the following response:Core_6506#ping Protocol [ip]: Target IP address: 17.18.27.27 Repeat count [5]: 10 Extended comma...

LMS 3.2-2.6 : migration and master/slave

Hi, Customer has 2 LMS 2.6 standalone server, server A and server BHe wants to migrate both to 3.2 and he will have a new LMS 3.2 server C.He would like to have server C master and server A and B slaves. Do you think that we can migrate server A and ...

Network Management

Forum Posts

Linksys router, problems with SNMP

Is it possible to do EoX/PSIRT reporting against configs collected by another tool ?

Resolved! Customizing HUM graphs

Resolved! Update on Cisco Works Open Database Schema Support dbviews document ?

LMS 3.2 - RME System Inventory Polling takes very long

View NetFlow Data in CiscoWorks LMS 3.1?

File Format for export from Ciscoworks to ACS

Resolved! 403 forbidden error while trying to access CiscoWorks(LMA ver 2.6)

Resolved! CiscoWorks Usertracking problem

Resolved! EEM - "action" not taken on another router with similar IOS

DCR Add Device shows Duplicate Device Name

Topology map not working in LMS 3.1

Query about accessing WiSM in Cat 6509 through session slot command

Resolved! Extended Ping command "Loose, Strict, Record, Timestamp, Verbose[none]:" explanation needed

LMS 3.2-2.6 : migration and master/slave

Get ready! Great things are coming to Cisco Community

Have your wish for humanity broadcast into space by George Takei!

Cisco Prime 3.9 logging router when Interface Up/Down

Error in Cisco BGP YANG module

SNMP Server only discovers one switch out of 6 network devices

Wireless Distribution System OR bridging using Cisco packet tracer

Cisco PI - Syslog Streaming Performance

How to connect 3 ASR-1001-X routers through tunnels.

SNMP V3 read only setup

Retransmission flood of FIN, ACKs from DNS server...

Unable to ping to External Internet

EEM CLI command character limit