I tried to change device configuration using my username, but Change Audit shows configuration changed by cisco username, not my username. How to get it fixed. I'm using LMS 3.0.1 installed on Windows
I tried to change device configuration using my username, but Change Audit shows configuration changed by cisco username, not my username. How to get it fixed. I'm using LMS 3.0.1 installed on Windows
We currently contract the monitoring of our domestic ports (T1 and above) using Cisco's Frame Plus service which includes dependance on leased/managed equipment such as a Kentrox, Zhone and now GDX Xedge multiplexers. Well, we're looking to move awa...
Hi,We encountered a problem with Device Center particularly on its UT End Host report tool. We tried doing the report for the Cisco 4507 switch with 2 x 48 port modules installed. A total of 58 ports are set as access ports but the report only shows ...
My boss is asking about the administrative ability of Ciscoworks where we would create sub-accounts (for lack of a better term) where we can create an non-admin account, and give that account access to only his own core switches for config archive ac...
I have a remote office. I need to configure a VLAN for guest internet access. I have created the VLAN and am using sub-interfaces on the router. I want to rate lime traffic to ensure a guest does not take up all the bandwidth. CAR (Committed Access ...
Looking to use SDM on 2621xm router to do VPN over DSL. SDM is working properly. Does it support VPN tunneling? Any ideas?
Hi,I was wondering if someone please advise on what Java version I need to run Cisco works 6.0 nad later without error? as is i canot run the campus manager at all given the unsupported java version on my pc. I am acessing this application via brower...
For some reason I am unable to gain access to the HOME, DEVICE and CREDENTIALS and GROUPS tabs under the Common Services. When I click on any of those tabs, it begins to load then stops 1/2 way and sits there. I am running LMS 3.1
Hi,we use a lot of accesspoints AIR-AP1231G-E-K9 and I want to generate an inventory report of theese devices.OID: .1.3.6.1.4.1.9.1.525But some of the devices are not shown valid (screenshot), others are right.The IOS is the same on all devices.The o...
Hi,I know that it's possible to create different groups of devices in LMS through ACS, in such a way that a specific user cannot access to devices not assigned to him.Is it possible to do it with a FreeRadius instead of a ACS?Many thanks.
We are running Ciscoworks 3.0.1 on ESX 3.5. I know VM's don't handle Java well without doing some tuning. Does Cisco provide any guidelines for VM tuning for Ciscoworks?
I have device already defined in CiscoWorks through Loopback interface. The problem is the same device keep coming up in the device discovery through PortChannel interface, which is a different IP address, so it looks like a new device. Is there a wa...
Hi Expert,I managed to upgrade the NAM software from version 3.6(1)to NAM version 4,but now i'm facing another problem is that,the previous working reports e.g.: Top Applications, Top Conversations...now is not longer running even though i enable man...
When I try to start a Device Managebility Status job, he tells me "DM0032: You have not selected any devices. Select at least one device.". But I selected 107 devices.Why does this happen?
Hi all,When I execute this report the next error appears"Unable to get data from Cisco.com. Check Cisco.com connectivity. Try again later"Others reports that it needs Cisco.com credentials works fine.I attach doc file with screenshotsAny idea?Thanks
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
04-16-2024 04:45 AM | ||
04-16-2024 01:33 AM | ||
04-13-2024 12:00 PM | ||
04-11-2024 05:18 AM | ||
04-08-2024 08:39 AM |
User | Count |
---|---|
7 | |
2 | |
1 | |
1 | |
1 |