Could I use Ciscowork2000 to monitor non Cisco deivces; for example, IBM hubs and APC UPS? And How can I do that? My basic goal is to use Ciscowork2000 to inventory all devices.FYIThanks:-)
Could I use Ciscowork2000 to monitor non Cisco deivces; for example, IBM hubs and APC UPS? And How can I do that? My basic goal is to use Ciscowork2000 to inventory all devices.FYIThanks:-)
We have Cisco SNMS installed along with some 3750 which are setup as a stack.Does anyone know how to monitor this in whatsup Gold.For example if the middle switch in the stack powers off then it sends an alert to whatsup gold to state this switch is ...
(I hope, there will be no double poste, as my last one was not sent or posted)Hi,On this post ( http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1dd750db) , I asked how it is possible to con...
Is there a way I can configure IPM to send an e-mail notification when there are errors for collectors in the Alert reports? Thank you in advance.Best Regards,Santi
Does anyone know how to setup my 3660 to boot from the IOS loaded on the PCMCIA card? Currently when I reboot the router it comes up in ROMON mode and I have to enter the command: boot slot0:Thanks!Dave
I've got CWSI running CM 3.3 with IDU 10, RME 3.5 with IDU 10 and the Cat4000IOS version 10 package installed. When I go to distribute images I cannot make the Cat4506 show up as a possible device to update the IOS no matter what I do. I have the 12...
Hi,I just heard that Cisco is offering previews on LMS 2.5 in Danmark. Unfortunately, I'm more than 1000 km south in Switzerland. Could anyone give some details about this new version?Many thanxGeorg
Hi,could anybody please explain what does " Minor Acquisition" exactly mean?The on-line Help says:"During major acquisitions, the ANI Server reads data from the bridge table of switches and the IP table of routers in the network and updates the end-u...
Hi,I've been experiencing a problem after installing RME IDU 10. I recently did a fresh install (with update 1 and IDU 5) of RME and it ran perfectly. Then I installed IDU 10 (I double checked that I had installed all the prerequisites) and now I'm h...
In cisworks RME syslog analysis when i want to see the syslog of any device i get an error. Please check wether logging is enabled on the device.I have restored the database, but still i am not able to see the syslog.Users who check the syslog via we...
Help appreciated.Running Win2k server with SP4 and RME3.5. Priviously, all services and modules were working. However, after a adware and spyware attack, only the RME module wasn't working. Tried uninstalling and reinstalling back the rme module, the...
Hello,Is their any software through which we can monitor the Internet Bandwidth of the Individual PC in the LAN??Thanks in advance Vijay
Hi,I'm currently using Ciscowork2000 4th edition. I have recently changed the IP address of a couple of cisco switches. The aniserver has discovered the new ip addresses for these switches, but it is also showing the old IP addresses aswell in (serve...
I've got 1710 router running c1710-k9o3sy-mz.123-11.T3.bin image. I'd like to install SDM 2.0a including IPS with custom signatures. The problem is that there is not enough free space on the built-in flash memory. Unfortunately, this routers flash i...
I know this is a "it depends" question but need to ask just the same. How much file space does RTM need on a Solaris platform for the app and the db it builds. I know the majority of that will be in /OPT. Hopefully, the "estimate" is easier to figur...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 03-25-2025 10:20 PM | ||
| 03-20-2025 08:27 AM | ||
| 02-05-2025 06:37 AM | ||
| 01-23-2025 12:17 AM | ||
| 01-20-2025 02:42 AM |
| User | Count |
|---|---|
| 3 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |