Network Management

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Webinar

 
Labels

Forum Posts

I have been tasked with getting core dumps from all of our customer routers (about 120). Is there a way to get CW to send these files back to itself? I was think of creating a Netconfig job to do this.I am running LMS 2.2 with all updates and patche...

vnealy by Level 1
  • 2871 Views
  • 1 replies
  • 0 Helpful votes

We're currently running the LMS 2.1 on W2K and would like to port it to the VMWare platform. Has anybody tried to use VMWare as the platform for CW2K and have any suggestions for it?Thanks.

axfalk by Level 1
  • 2710 Views
  • 1 replies
  • 0 Helpful votes

Hi, ive installed the following:CD One Fifth Edition 2.1 Campus Manager 3.2 Device Fault Manager 1.2 Device Fault Manager Incremental Device Update 1.2 Resource Manager Essentials 3.4 Resource Manager Essentials Incremental Device Support 3.4 proble...

noctorno by Level 1
  • 2986 Views
  • 3 replies
  • 0 Helpful votes

I am trying get CW2K to authenticate through MS AD and am not having success. In the Login Module Options in the server box, I have ldap://mbhdc5 (which is the primary DC in our AD). in the usersroot, I have dc=mbh,dc=mhs,dc=magellanhealth,dc=com I h...

g.hammond by Level 1
  • 2808 Views
  • 1 replies
  • 0 Helpful votes

We're useing two 4506/Sup4's for our primary and backup server switches w/ HSRP between the server Vlan defined on both. Ngenius was monitoring the primary fine, but when I added the secondary a few days later it started sending ARP traffic bursts e...

philh70 by Level 1
  • 2855 Views
  • 1 replies
  • 0 Helpful votes

Is there a way within Netflow to track the AS, or AS Path that our internet traffic is going to? We have multiple ISP's and I am trying to find a way to "Balance" traffic across these providers. One suggested using Netflow to track this information.T...

jogreco by Level 1
  • 3068 Views
  • 2 replies
  • 0 Helpful votes

I have a pretty elderly Ciscoworks installation and after suffering from a corrupt database I am trying to build a new one on my Ciscoworks installation. I have, as advised,used the original files to create a new blank database into which I'm trying ...

d.briody by Level 1
  • 2895 Views
  • 3 replies
  • 0 Helpful votes

HiWe have CiscoWorks installed on a SUN unix workstation. From a lot of reasons we didnt use it.Now I am trying to start using the program again... And I'm wanted to know which platform is best for using CiscoWorks?It need to be based on:1. Performan...

We are looking to graph the "reliability" counter that is displayed in the "show interface" command. I have found locIfReliab at 1.3.6.1.4.1.9.2.2.1.1.22, but the Cisco MIB Browser Utility lists this as part of the "OLD-CISCO-INTERFACES-MIB". Does ...

grayd by Level 1
  • 3134 Views
  • 1 replies
  • 0 Helpful votes

Hello all,This is my first try at using Cisco anything. I am having trouble setting up vlans on a 1200 ap using procurve 4000 switches. I need two vlans , one for data, and one for ip phones (which will be broadcast ssid). The problem comes when I ma...

I have installed the LMS bundle with RME and DFM running on the same box. RME is 100% working correctly. I went to work on DFM and I can't attach to the domain. Has anyone run cross this before and if so how do you resolve this issue.

efisher by Level 1
  • 2898 Views
  • 1 replies
  • 0 Helpful votes

Review Cisco Networking for a $25 gift card