Hello Im having problem with GRE tunnel connecting cisco and mikrotik routers, have tried many different configurations but none seems to work, tried disabling firewall rules on mikrotik, tried to turn off keepalive on mikrotik gre, tried to keep ...
Forum Posts
Hi Anybody, we're facing an issue with old Client Session History stored in Prime DB and are not deleted, even if it shold. In Administration --> Settings --> System Settings --> Client and User --> Client --> Data Retention we set the following:Disa...
Hello does anybody knows how to make Cisco Prime Infrastructure 3.6 able to deploy more than 5 devices at one instance? according to the cisco documentation for prime it says:"Prime infrastructure allows you to use a maximum of one Local file server ...
We are currently using Solarwinds to run Compliance Reports for all our Cisco hardware. One of the criteria is Disabling reverse telnet on these devices.Previously I have done this under 'Line-console-0transport input/transport preferred noneThis ha...
Network management or monitoring? Scope of the question:For my company (with a very large network) I'm writing a research to develop a Network Monitoring capacity for a part of the network. Previous phrase was provided by my superiors and in my opi...
Resolved! Cisco 2960X stack version of ios
Hello supporti have used Cisco switch (Catalyst 2960X)i want to stack them, and i'm not sur if the version of ios is supported or not Attached is the sh version of my switches with the current version, can i stack my switches? Please help Regards
Good day, tell me why cisco asr 9001 ver xr 6.5.2. changes the status of the radius server to dead? debug below. server 10.32.0.60/1812/1646 UP->DEAD RP/0/RSP0/CPU0:Jan 20 10:26:43.590 MSK: radiusd[1137]: ip add v6 existing len: 16RP/0/RSP0/CPU0:Jan ...
Hello, Let me preface my question with: I am no networking admin. At all. My system is a live entertainment system. I have a "controller" going to a 200 series switch, going to an SFP switch, then into several different switches over fiber. I wan...
hello guys, anyone familiar with a way to see a logg of executed commands history?one of our customers had a service down because someone entered a 'shutdown vlan XX' command on the NFS vlan. i know there is such log file in Juniper and HP. thanks i...
Catalyst 3850-24S-S Switch configured as core switch, VLANs for telephone system, network and Wifi are working fine as the end devices are also Cisco. But we have Fire alarm (Edwards Detection and alarm) Vlan161 and BMS (Honeywell Alerton) Systems w...
Recently I installed Cisco SG350-K9 Series Managed Switches 52 port in both offices. Office A (Old office)Equipment's:1 Cisco SG350- 52 port Switch (192.168.1.1)2 FTTH 200mbps Internet3 Dlink IP Telephone PBX4 Telephone 1 line. to use with office A ...
Resolved! how to add an unmanaged switch to RV325
Hi, I surrender, LOL. I have several unmanaged switches here. I need more ports than the RV325 has. Everything is wired. Must be some fundamental thing. I cannot get an IP from the RV325 in DHCP mode to anything connected to a simple switch. Everythi...
I have a Cisco 1921 I am wanting to use for internet connections at home. My internet service provided is spectrum and I have a modem I want to use for this. I would like to use G0/0 to go from the back of the modem, to the router. So this would be t...
Hi, how are you?I need help , with connecting my server pc to ethernet i can see him with the WIFI , but if i connect my server with WIFI , i cant see my server and my pc.If server is with ethernet , i can see this pc too. Im using a CISCO RV 340W , ...
I have some licenses available in PI, but when I try to add a switch I get , " No valid device is selected to change admin status " when it is in the unmanaged state, after adding it. One of these would tell me , before I could add it, that the IP ...
