Network Management

hello i would like to use centreon to get temperature value and chassis status with snmp v3 on CISCO DENALI 3650which  OID to use ?i m using check_centreon_snmp_traffic for interfaceswhat are the number of  interfaces gigabitethernet 1/0/1 and so on ...

Where can I find the release dates for the firmware / software for the DPC3941T? Gateway has the following System Software Version listed. eMTA & DOCSIS Software Version: 2.3.10.13_5.5.0.5 Software Image Name: DPC3941_3.6p9s1_PROD_sey  

Hi everyone,  I would need some help with LLDP, my goal is to enable LLDP vlan-id on ASR9K, but I am not able to do it.   RP/0/RSP0/CPU0:AQA_ASR_2(config)#lldp tlv-select ?management-address Management Address TLVport-description Port Description TLV...

Does anyone know if there is another support avenue for AT&T circuit testing and support. I've used the (888) 613-6330 support number but support there has gone down hill to being just bad. I just was wondering if there was a US call center they don'...

Hi there,             I want to use solarwind to monitor the time accuracy of cisco switches(3850). Now I have NTPv4 enable to a testing switch as NTP client. I setup a domain controller as NTP server. It's properly synced by showing ntp status. Then...

Can anyone tell me what the issue is here: netadmin@bnaplxjmpnet:/etc/ansible$ sudo vi asa03.yml ---- hosts: B_ASA   tasks:    - asa_command:        commands:          - show version        provider: "{{ cli }}"      register: output     - debug: var...

Hi ,  For one of my project i want to configure a switch  using C++ . is it possible ? My configuration requirement  is to  switch on and switch off  one by one for each port  :- Using command switchport On and  then switchPort off  ( at a time i wan...

I am trying to poll the min and max source to destination and destination to source IP Sla statistics from some Cisco devices.  I am using the following OID's:   .1.3.6.1.4.1.9.9.42.1.5.2.1.6 --> rttMonLatestJitterOperMinOfPositivesSD .1.3.6.1.4.1.9....

Hello All. I have Cisco 4321 as NAT and GW device for my server. I need and IDS/IPS for security and i need some suggestion for this, can anyone help me please. I'm thinking about buying ASA5516-FTD-K9 or buying UCS E-Series Server Blade and run UTD ...

Hi,Several years ago, I've developed a C++ process (running on Linux RedHAT 7) that connects via SSH to Cisco routers (IOS 12.2).The process's task is to monitor (retrieve&update) some preconfigured ACL and it uses the libshh 0.7.0 version (https://w...

Good day everybody,Due to the horrible offset time at the access switches, the sync procces takes days sometimes weeks to update.Any idea what's going on ?- the ntp server is the destribution switch me3800x. It listens to ntp clients (the access swit...

New to ansible and have a quick question.  When running a simple playbook to show version and show running and append to an output.  The output puts quotes around everything and displays the \n for a carriage return instead of going to the next line....

HiThe NAM theme is new to me and I have a question about that:Is there a posibility to capture only TCP Retransmissions or much better if TCP Retransmissions ocure for examples if 50 TCP Retransmissions  happen in 10 Seconds then start a packet captu...

I've recently inherited an existing Prime Infrastructure server and have been struggling to get my head around how to silence some spurious alerts. At present there is a WLC in the network that is using a single Ethernet link into the network, with t...