Buy or Renew
Buy or Renew

Network Management

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

EEM : traceroute output to a file

Hi,I am working on an applet which would get triggered if there is a state change on an object.One of the requirements is to collect the traceroute output.I am able to append the output of most of the commands to a text file but not the output of tra...

nhura by • Beginner
  • 5479 Views
  • 9 replies
  • 0 Helpful votes

Resolved! Where can I find netflow fields details?

Hi,   I have a sampled netflow log in csv. Is there a documentation that will explains what every column means? example, "input, output, first, last, tos, acl_flag etc. Some looks very direct but I'm just guessing of the the terms and I want to check...

wuming79 by • Beginner
  • 1025 Views
  • 1 replies
  • 0 Helpful votes

To disbale ssh v1 on router 3900

Hi All,   When I  run the command  show ip ssh on the router  below is the output .   show ip sshSSH Enabled - version 1.99   I believe it is supporting both version 1 and version 2.   Need to disable ssh version 1 only  and allow version 2 . Kindly ...

Need OID for rxload and input rate

Hi all,I want to monitor the rxload and input rate on interfaces but I can't find the correct OID can someone help me with this please.Can someone also provideme a good document for thisGigabitEthernet4/8 is up, line protocol is up (connected)  Hardw...

gurkamal01 by • Beginner
  • 9169 Views
  • 6 replies
  • 0 Helpful votes

CISCO Network Assistant Topology View

Hi I have a quick question about the CISCO Network Assistant Topology View, sometimes when CNA discovers a new switch is Places it outside of the Topology window so you cannot see it?  how do I then drag and drop the switch to where I want to see it?...

jodan by • Beginner
  • 2959 Views
  • 9 replies
  • 0 Helpful votes

DCNM MIB support

Hi everyone,   Can you know if the Cisco DCNM can read all MIBs supported by Cisco NX-OS (Nexus 5600)? I'm refering about MIB I, MIB II and private MIB.     Thank you very much!   Allyson  

apereira3 by • Beginner
  • 991 Views
  • 0 replies
  • 0 Helpful votes

Resolved! IP SLA with Object Tracking PROBLEM

Hi, I have a problem with the 2 SLA that I am using to get EEM script and Failover.I have 4 tracks that I am ussing 2 for 1 SLA. My conifg is the next: ! track 1 ip sla 1 reachability delay down 6 up 6 ! track 2 list boolean and object 1 not ! trac...

farguisito by • Beginner
  • 3810 Views
  • 13 replies
  • 0 Helpful votes

Resolved! DHCP Assignment Event

Hello all, Does anyone know a way of triggering on assignment of a DHCP address to a router?  Is it easier to catch it as a syslog event?   if a router is configured with: interface g0/0   ip address dhcp    ip route 0.0.0.0 0.0.0.0 dhcp

Resolved! Script to stop and start a capture point

Is it possible to write a script that would start a capture point and then stop it after 5 minutes and then export it to a tftp server, then again wait for few minutes to re-start the capture point and repeat the whole process again?   We need to cap...

cofee by • Contributor
  • 1765 Views
  • 6 replies
  • 0 Helpful votes
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers
Spotlight Award Nomination