Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
Hello, Everyone.
I'm having problems with my ACS 5.5
After boot, the ACS does not start the processes 'management' and because of that, other process don't start as well.
acs2/admin# show application status acsACS role: SECONDARYProcess 'da...
I have configured Captured Session through my "NAM2420" Cisco Prime NAM having Software 6.2. While trying to download the file I am getting below error.
" Access is Locked. Please try again in few seconds"
I am unable to find any known issue rela...
Below is a partial config that I am using for a cisco 3850 L3 switch. We are trying to monitor network traffic to a Solarwinds server. Does anyone notice anything out of the ordinary?
I have only recently hired on at this establishment and this is so...
Does anyone know how I can get expect to detect different platforms? I like to run different commands for different platforms.
If IOS
username admin privilege 15 secret xxx
If Nexus
username admin password xxx role network-adminstrator
If ASA
...
Hello, I'm coming back to you for a new problem
We have in our infrastructure two Nexuscisco Nexus9000 C9372TX chassis
These Nexus are only used to connect all our ESXI created several Port Channel with VPC
When I look at the logs, I see these differ...
Hello, how that I have TACACS running on my device, I notice that the syslog messages for login success have changed i.e. they no longer include a 'Source: x' field. Is there anyway to change this to include a source ?
EXAMPLE OF LOGIN SUCCESS SYSLOG...
Hi All,
I'm working on creating an EEM script which is working fine for the most part of it except one thing.
I'm trying to redirect the output of ping results (run on an IOS router) to a file in the flash however having a hard time finding the right...
Hi all,
I have a Cisco 3825 with Version 15.1(4)M12a, RELEASE SOFTWARE (fc1) with one Serial Interface. I have added this router to my Cisco Prime 3.2 instance but can't see the Serial Interface. Do I need to add a special configuration to Prime to...
Hi!
I want to use advanced routing at Linksys WRT300 in Packet Tracer.
In my version 5.3.3.0019 there is advanced routing deactivated.
Hope somebody can help me there.
kindly regards
I've got a Cisco ASR running version 16.6. Currently, I've got RESTCONF working, but I'm unable to retrieve any interface information with a GET request. I'm guessing I need to install a data model, but I'm not really finding any detailed information...
I have a Cisco ASR1009-X running IOS XE 16.6.2. I'm trying to get RESTCONF working, but having some issues.
If I try a curl request, I get a '401 authentication needed' error. In my curl request, I'm specifying the username & password, but I'm assu...
Hi
I'm trying to create a fairly basic EEM script to capture certain command outputs when the traffic on a sub-interface exceeds a certain threshold. I was able to do so for the interface using transmit_rate_bps but this parameter is only for the phy...
Sirs,There is no snmp-server enable traps configured. The show snmp confirms that snmp global trap and snmp logging are disabled. The only command configured is snmp-server community XX . Why when I run a scan tool it shows that port udp 162 (snmptr...
Hi,
Software: Prime Infrastructure 3.3 / 3.4
which settings have to be enabled to get the client device tracking (Monitor --> Clients and users) for wired users working?
We have a wide range of 2950/2960s,x,3850 switches in full managed status but ...
Hi,
I'm facing a problem with the installation of NIM-SSD on cisco ISR 4330. my NIM-SSD state is out of service after booting state for couple minutes.
i was search the procedure to install it but not found something really technical procedure to i...
