Good morning all, I'd like to replace some of my current HP switches with new Cisco devices, and I'd like to know the best corrisponding model. I have the following models at the moment: HP 2530-24GHP Procurve 2810-48GHP 2530-48G PoE+ARUBA 2530-24GAR...
Forum Posts
Hello,I just got my hands on a Catalyst C2960S-48LPS-L that I will be trying to learn Cisco networking with. I've already factory reset it and set an enable secret, hostname, etc. thru the beginning setup wizard in the console. I'm just trying to cre...
I had to reinstall MSE.8.0.110.0 -> 8.0.150.0 However, after reinstallation, new wireless users cannot connect. The settings of the existing MSE are unknown. It seems that the WIPS function is turned on in the newly reinstalled MSE (this is not accur...
Hey Everyone!So I really want to get rid of the TACACS+ we have and set a SSO or some kind of token authentication.Now I know that it might be impossible or hard, but I hope I'm wrong.Is there someone here who has any idea how can this be implanted?
I'm configuring SNMP for L2 & L3 switches.While configuring snmp traps i'm able to understand some commands but unable to understand some commands also.So unable to decide which all commands should i add as don't know the piece of information it will...
Hello!After upgrading to EPN Manager 7.1 an error occurs when trying to download any report from EPN Manager GUI. When Download button clicked, the following GET request to the server is generated -h**ps://<ip_address>/webacs//localdisk/ftp/reportsO...
I had intermittent ping drop issues which initiate ping from the switch itself when ping to it's own SVI ip address Switch#show ip int briefInterface IP-Address OK? Method Status ProtocolVlan10 192.168.24.14 YES NVRAM up up p...
Hi Guys,Is there any chance to check and change the threshold of alert on Cisco Prime Infrastructure? I want to check the current threshold for "AP Client Count Threshold Violated" and "AP Client Throughput Threshold Violated" alerts and might adjust...
Hello, everyone!I have a question about how WRED works as I find it very confusing. I understand what WRED is and what goals it aims to achieve during congestion (drop packets, avoid Taildrop and so on).However, the actual principle of it is quite co...
Hello Cisco Help, Does anybody know why I am unable to ping my pc to the router or ISP into the other subnets? I am quite bad at this and don't understand what I did wrong. PC0 can ping the local switch, but not the router.G0/1 is up and so is GIG0/0...
Hello, I have a weird situation where i get in logs that mac address is flapping:264094: *Nov 7 15:10:32 GMT: %SW_MATM-4-MACFLAP_NOTIF: Host 4c52.6211.ac36 in vlan 19 is flapping between port Twe1/0/24 and port Twe2/0/24264095: *Nov 7 15:10:47 GMT:...
Hi Company has two links to ISP or two ISPs. There are a few bgp attributes that can be used to decide which link of the two can be primary or second link. such as for route inbound local preference, weight, and outbound MED and as-path etc.So usuall...
Since we've replaced our Internet router with a IOS-XE C8000 router, the ifHCOutCounters generate regular spikes like shown below.This happens normally when the router reboots and the counters are reset on the device and generate a wraparound in the...
Experiencing extremely slow transfer times using scp to transfer an IOS XE image to an ASR-1002(X). Have attempted using three different routers and two separate servers. In all cases scp is extremely slow. A 380MB image is still transferring afte...
Hi,I have a question regarding the following article:https://www.cisco.com/c/en/us/td/docs/cable/cbr/configuration/guide/b_cbr_docsis_full_book_xe16_10/b_cbr_docsis_full_book_xe16_10_chapter_0100110.htmlThe article indicates that we can receive spect...
