There are Community messages dating back to 2012 noting this issue. If anyone from Cisco is reading this thread, is it possible to open a bug for this problem? In the meantime, has anyone come up with a workaround?
Posts de fórum
I am trying to figure out how to create a "named" counter in EEM. My goal is to:1 - Create a "watchdog timer" event applet that updates the subsystem "798 type 1" event every time it expires2 - Create a "none" event applet that is run from the CLI, ...
Hello,while trying to activate the licence for my cisco prime server, i needed the PID in order to generate the licence file on Cisco portalI used the CLI PID "Cisco-VM-SPID" which is wrong, since i had to use the PID dedicated to the GUI interfaceU...
Hi, Trying to create a Ring with a mix of IE4000s and IE4010s. I am using the guide by Cisco on MRP: Cisco Redundancy Protocol GUIDE I am following the step-by-step instructions to configure mrp, and the IE4000s work like a charm as mrp clients or ma...
It is possible that a client has migrated their entire data center to the Internet through Microsoft Azure services, and that an on-premises satellite server (SSMS) is installed there to synchronize the licenses of their Cisco routers and switches. D...
Resolvido! NetFlow Terms - Flow record
Hello guys,im studying NetFlow atm and I want to know if I understand the flow record correctly. Especially important for me to understand here, since im struggling with this a bit is the flow record "match" and "collect" statements.Flow record: The ...
Hi guys, I'm the new IT guy in a university, I just installed Wireshark to check network traffic and I saw some OSPF hello messages, it seems passive interfaces have not been configured, I thought...is this enough to infiltrate into the network and j...
Hello again, community.I'm currently looking for documentation on EEM commands as a whole. One that has me stuck, is having EEM send a message to all VTY lines. The reason behind this, is to send output in the event that my EEM fails. I've configured...
I have an eem "none" event applet that uses a wait action. I'd like to be able to pass in the number of seconds to wait as an agument to the applet. I'm able to use applet agruments ($_none_arg1, etc.) within CLI commands where a WORD is expected, ...
Hi Team,We need to sync the time of our ASR 9000 router with our custom NTP server. We are able to ping the IP of NTP server from management VRF. Can anyone please share the commands/steps to configure router.Thanks
MSE needs to be downgradedI found out from the TAC that it will be done in the same way as the upgrade. completed post install scripts in progress No longer progressed in the corresponding phrase. It was downgraded to 8.0.150.0 -> 8.0.140.0I canceled...
Hi,Not too familiar with Cisco products, but would just like confirmation that a switch product that is claimed or unclaimed is the same thing as checking if the serial number is Status Covered / Not Covered?I've seen a different dashboard portal for...
Resolvido! EEM: regexp not returning all matches
So I am trying to parse all the whitespace out of a string like: "gig1/0/1 - 2 , gig 1/0/5 , 6, 8, 9"I used an online regexp checker to come up with the following search string:Does exactly what I want. But when I try to use this same search string ...
Resolvido! SNMPD Service Crash on N7710
Dear Cisco Community,I hope this email finds you well. I am reaching out to the community seeking assistance with a critical issue I've encountered in one of the virtual contexts on my Cisco Nexus 7710.Problem DescriptionFor the past few days, one of...
Attempting to use a Putney Bowes Postage meter printer Model 8H00 to connect to our Cisco 9300 switch using the built in wired connection on the device. Cisco Switch is PID: C9300-48UXM and running version 17.06.05. When attempting to connect ...
| Utilizador | Contagem |
|---|---|
| 3 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |
