Buy or Renew
Buy or Renew

Network Management

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Update to Prime LMS 4.2.3

HelloAfter update to LMS 4.2.3 is get always a message to confirm when login:"Server is capable for performance tuning. Please enable PTT ...."            Even when i setup PTT the message will come again next time i login.The message comes also seve...

mchristen by • Beginner
  • 683 Views
  • 2 replies
  • 0 Helpful votes

RME compliance template question

Using LMS 3.2, I've started learning how to use the compliance templates. I have a question regarding the regex matching, and I can't seem to findan answer in the docs or in the forum posts. I do admit that I have not dug real deep in the forums.My q...

cmarva by • Enthusiast
  • 406 Views
  • 1 replies
  • 0 Helpful votes

PI is Trap receiver

Hi NMS community I just installed PI 1.2  in the Lab.PI is of course also a trap receiver which get in traps with a community,Where can i configure the trap community for Prime ( not the one for the network elements ) ?ThanksKarl

Cisco LMS 4.2

I need your help to get starting the configuration of Cisco LMS v4.2 , i have already configured all switch and all routers with SNMP . I need a steps to configure LMS server v4.2.

Resolved! LMS 4.2 critical alert in email

Hi all,I have an issue with my lms 4.2 installation.I have created a fault notication group which sends me an email when an alert is active on a device.Some of the devices are deleted from the inventory, but when I restart my deamon manager. I receiv...

ASR9K NP controllers drop counter monitoring

                   Hi, TeamCustomer asked to check np drop counter from their own ASR9k. If there are any controller its drop counter is over 0, wanna get syslog.Sample result of command as following.RP/1/RSP0/CPU0:ASR_02# show controllers np counter...

jaemlee by • Cisco Employee
  • 2196 Views
  • 3 replies
  • 0 Helpful votes

EEM: "event routing network" vrf aware?

Hello everybody!I've 2 questions related to above topic:1.) how do I get the vrf information for a route beeing changed.2.) how do I track all routes in the routing table. including default-route The following command: event routing network 0.0.0.0/0...

rokraus by • Beginner
  • 2810 Views
  • 2 replies
  • 0 Helpful votes

Monitoring IPv6 BGP Peers via SNMP

I'm running 12.2(33)SXJ1 on a 6500 with several IPv6 BGP peers. Is there any way to monitor the BGP status of IPv6 peers? I've been through the BGP4 mib and cant seem find a way to check the status of IPv6 peers. Does anyone have any thoughts on this...

SNMPv2-SMI::mib-2 = No more variables left in this MIB View (It is past the end of the MIB tree)

Hi,Would like some help with the following error message:SNMP:             bash-3.00$ /usr/sfw/bin/snmpwalk -v2c -c <community-string> 172.17.6.224SNMPv2-SMI::mib-2 = No more variables left in this MIB View (It is past the end of the MIB tree)bash-3....

jdaby by • Beginner
  • 26864 Views
  • 1 replies
  • 0 Helpful votes

LMS 4.1 Housekeeping

Hello all,My job descritpion is network administrator/engineer. But for years I have been in charge of CW and now LMS 4.1. Since I am not a system engineer in profession, it has always been difficult for me to understand how to keep databases and log...

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers
Spotlight Award Nomination