Cisco ENCS 5412 WAAS

[saeedek]

Dears,

I have Cisco ENCS 5412 with Waas installed on it (Cisco ENCS 5412 WAAS )

how to login it and start configuration .

It's new device

[marce1000]

 https://www.cisco.com/c/en/us/td/docs/app_ntwk_services/waas/vwaas/vwaas-641/encsw-quick/encsw-quickstart.pdf

 M.

[saeedek]

thanks marce1000

but i need video or any material explained step by step.

Now i have Vwaas already installed on ENCS.

how i can login to ENCS ?

how i can login to Vwaas?

how can i start console configuration for Vwaas?

[pabubendorf]

I had to figure this out on my own as well documentation is not so great.

1. Configure the CIMC

- Connect serial cable to cimc and do the following:

Connect to CIMC Serial Port

login: admin / password

Set CIMC IP:

scope cimc
scope network
set v4-address 172.31.x.x
set v4-netmask 255.255.255.0
set v4-gateway 172.31.x.1
commit

Set CIMC Password (admin)
scope user 1
set password
 **enter password twice**
commit

Enable Serial over LAN (Console access for Vwaas)
scope sol
set enabled yes
commit

[saeedek]

dear pabubendorf
thanks for your reply.I have one question.
after i configure CIMC IP through CIMC console .i will use this IP for SSH when i connect to MGMT-CIMC
that is right ?

[pabubendorf]

Correct.

[pabubendorf]

To setup the Vwaas:

- Connect to Vwaas via CIMC Management Port

- ssh to ip assigned to cimc management port

-connect host (this will give you console access to Vwaas)

or

connect serial cable to console port on ENCS 54XX this will also give you console access to Vwaas

login: admin/default

To setup Vwaas - I like to use setup command easiest way to just get everything setup if you don't aready have a config built up.

**Few things to note**

- Vwaas Network Management Ports are the Built In Gige 0 or Gige 1, but they are called out in Vwaas as Virtual 1/0 or Virtual 1/1 I think. 

- Vwaas intercept mode, options are wccp or appnav, unless you purchased an inline card than its Virtual Inline 3/0 or Virtual Inline 3/1.

After you have completed setup accept the settings and your done.  You should be able to SSH to the assigned Vwaas IP Address.

If your adding it to a WAAS Central Manager you will need to do CMS enable if its not in your CM Manager yet.

[saeedek]

dear pabubendorf

many thanks for your support . i have one question can i access Vwaas through HTTP/HTTPS if yes how??

[VloT]

After initialization step, i have a 10.20.0.0/24 route in the wass routing table. I don't want this route to be involved in routing decision for traffic that need to be accellerated.

wae02#show ip route
Data Routes
-----------
Destination      Netmask          Gateway         Interface
-----------      -------          -------         ---------
0.0.0.0          0.0.0.0          10.10.90.97     Standby 1       
10.20.0.0        255.255.255.0    --               Virtual 0/0     
10.10.90.96     255.255.255.240  --               Standby 1       

Management Routes
-----------------
Destination      Netmask          Gateway         Interface
-----------      -------          -------         ---------

How can i remove/disable this automatic configuration?