Network Management

How can I speak to a 헿헲헽헿헲혀헲헻혁헮혁헶혃헲 at 헟ufthansa 헔irlines?Phone assistance: One of the quickest ways to speak with a 헟ufthansa 헔irlines support agent is by calling ++ퟏ(ퟓퟕퟑ) ퟔퟎퟔ-ퟒퟓퟐퟎ.// +ퟏ ퟓퟕퟑ ퟔퟎퟔ ퟒퟓퟐퟎ. The phone number for 헟ufthansa 헔irlines assistan...

How can I speak to a 헿헲헽헿헲혀헲헻혁헮혁헶혃헲 at 헟ufthansa 헔irlines?Phone assistance: One of the quickest ways to speak with a 헟ufthansa 헔irlines support agent is by calling ++ퟏ(ퟓퟕퟑ) ퟔퟎퟔ-ퟒퟓퟐퟎ.// +ퟏ ퟓퟕퟑ ퟔퟎퟔ ퟒퟓퟐퟎ. The phone number for 헟ufthansa 헔irlines assistan...

How can I speak to a 헿헲헽헿헲혀헲헻혁헮혁헶혃헲 at 헟ufthansa 헔irlines?Phone assistance: One of the quickest ways to speak with a 헟ufthansa 헔irlines support agent is by calling ++ퟏ(ퟓퟕퟑ) ퟔퟎퟔ-ퟒퟓퟐퟎ.// +ퟏ ퟓퟕퟑ ퟔퟎퟔ ퟒퟓퟐퟎ. The phone number for 헟ufthansa 헔irlines assistan...

Hello Everyone,I'm novice to networking. And below is the requirement I'm trying to figure out. Any leads would be greatly appreciated"You are working as an IT architect for a new startup business that grew faster than expected. they expanded to oper...

I'm having problems setting up my home network using Cisco2921 for the first time. It has the basic licenses only. Below is the running config followed by my adapter settings. Any assistance would be greatly appreciated. Thank you.Current configurati...

I have a couple of Cisco Firepowers that I can access thru SSH or the FDM, but I can't console to them?-Software version: 7.0.5-72-Configured with primary and secondary-Base license-Not using FMCCan someone tell me how to get console access? Thank yo...

Who do i speak with to make sure the switch is set up to allow communication between the equipment i am installing and the equipment on site. 

Hello Everyone,I work in a data center and we have two L3 Nexus 9k cores with 40g ports, then we have ~10 cabinets with 2 top-of-the-rack switches connected directly to the cores. Each TOR has connections for servers, ISP/MPLS routers, etc.I am tryin...

What have I tried?Once I connected the console cable to the router and my system, I checked that the USB port was available in my system and accessible.$ ls -l /dev/*USB* /dev/ttyUSB0 $ dmesg ... [22726.984409] usb 3-3: new full-speed USB device n...

We have configured two Lightweight Access Points using a 3504 WLC. Both access points are connected to the WLC, and have been assigned IP addresses through DHCP from the WLC. Both also state they are providing the WLAN we created. Authentication for ...

switch is running in install mode, i can see files in .pkg format. I can't find a good documentation on how to backup the config files, need help.

Hi,We are finding that some router models are more susceptible to CRC increase/snr decrease than others and tend to lose sync more easily especially when it comes down to sudden spikes in crc indicative of REIN/SHINE issues. Im trying to determine wh...

I've setup an icmp-echo IP SLA on a Cisco C9300 to ping another device on our network. I'm now trying to monitor the amount of timeouts seen by the IP SLA job in our monitoring tool (WhatsUp Gold) but when setting up the monitor, the issue I'm having...