cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1598
Views
5
Helpful
3
Replies

How to see Bundle Traffic or usages

aguntukkk
Level 1
Level 1

i have done 10+10=20 gbps bundle 

 

how to see current usages on ether-channel 
is there any command to see

 

 

interface Port-channel1

no ip address

no ip redirects

no ip unreachables

 

interface TenGigabitEthernet4/7

description Port-channel1

no ip address

no ip redirects

no ip unreachables

load-interval 30

no cdp enable

channel-protocol lacp

channel-group 1 mode active

!

interface TenGigabitEthernet4/8

description Port-channel1

no ip address

no ip redirects

no ip unreachables

load-interval 30

no cdp enable

channel-protocol lacp

channel-group 1 mode active

 

How to see usage or current traffic on ether chanel through command mode ?
useing 7600 series router ?

I want to see live traffic

3 Replies 3

balaji.bandi
Hall of Fame
Hall of Fame

You can view below command :

 

show interface port-channel 1  <- this will show you 20GB in the output and usage

 

show interface port-channel 1 human (this will show you human-readable depends on IOS).

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

i am getting like this after putting the bellow command
sh interface Port-channel 1

Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 1w6d
Input queue: 0/75/31905/31905 (size/max/drops/flushes); Total output
drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 17112510000 bits/sec, 2061279 packets/sec
5 minute output rate 3404539000 bits/sec, 1369827 packets/sec
L2 Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes
L3 in Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes mcast
L3 out Switched: ucast: 0 pkt, 0 bytes mcast: 0 pkt, 0 bytes
1698525090631 packets input, 1706754566329303 bytes, 0 no buffer

i want to know traffic usages of sub interface of port-channel 1
Example:

sh interface Port-channel1.809

Port-channel1.809 is up, line protocol is up (connected)
Hardware is EtherChannel, address is 442b.03d7.2e00 (bia 442b.03d7.2e00)
Description: Summit-internet
Internet address is 10.56.78.10/30
MTU 1500 bytes, BW 20000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 44/255, rxload 218/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 809.
ARP type: ARPA, ARP Timeout 04:00:00
Keepalive set (10 sec)
1706155970998 packets input, 1698149313032370 bytes
1120982354916 packets output, 338106432748371 bytes
L2 Switched: ucast: 39156631 pkt, 3552660869 bytes - mcast: 6291 pkt,
767246 bytes
L3 in Switched: ucast: 1705993321791 pkt, 1698137138669658 bytes - mcast:
0 pkt, 0 bytes mcast
L3 out Switched: ucast: 1120842549144 pkt, 338095512247801 bytes mcast: 0
pkt, 0 bytes
Last clearing of "show interface" counters 1w6d



you see this here :

 

MTU 1500 bytes, BW 20000000 Kbit/sec, DLY 10 usec,

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help